9027 Desco, 9027 Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/1/190/desco_sml.jpg)
9027
Manufacturer Part Number
9027
Description
WRISTBAND ELASTIC LARGE 4MM
Manufacturer
Desco
Specifications of 9027
Strap Type
Wrist Strap (Wristband)
Size
Large
Color
Blue
Number Of Conductors
Single Wire
Strap Material
Elastic Fabric
Strap Termination
4mm Snap Stud
Lead Free Status / RoHS Status
Not applicable / Not applicable
Features
-
Cord Length
-
Cord Plug
-
Cord Type
-
Strap Closure
-
TB-2005 Page 2 of 2
Size Adjustment of Wristbands
Elastic Adjustable Wristbands
The elastic adjustable band is designed to
be adjusted to the proper size to fit each
individual wearer. After adjustment it can
be used as a fixed size band. It is only
necessary to adjust the size once.
1. Place the wristband on the wrist.
2. Open the clasp by pulling upward on
the “tail” of material that extends out from
the clasp.
3. Tighten or loosen the elastic material
through the clasp until the wristband fits
snugly but comfortably.
4. We recommend that you close the
clasp and wear the band with the excess
tail extended for a day to be sure the
adjustment is snug, comfortable, and has
the proper electrical contact with the skin
before cutting.
5. Test the wrist strap system to be sure
of proper electrical resistance and skin
contact. Use the procedure described
under “testing”.
6. When you are ready to cut off
excess material, mark with a pencil where
excess material is to be trimmed.
7. Remove band from wrist. Open
clasp. Cut off excess material about 1/4"
short of pencil mark so that the end of
material is concealed by the cap. This will
eliminate the possiblity of exposed frayed
ends.
8. Close clasp and use as a fixed elastic
wristband.
Replacement of Elastic Material
For use with 09028, 09069, 09070, and
91020 only. When the elastic material
becomes worn, it can be easily replaced.
Order item number 09029 from Desco for
a replacement strip. To replace the fabric,
DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Fax (781) 575-0172 • Web Site: Desco.com
DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178 • Fax (909) 627-7449
simply open the clasp as described under
“Adjustment”. Remove the fabric from the
clasp. Note that the second end of the
material is secured to the clasp by a
smaller camlock. Open the small camlock
(A small screwdriver is helpful.) Remove
the fabric and replace it with the 09029. Be
sure no material extends to the end of the
lever arm of the small camlock. This will
cause the clasp to close improperly and
not hold firmly.
Metal Expansion Wristbands
1. Insert the link end of the wristband into
the slotted opening on the cap. Insert it at
a downward angle to allow the links to
slide inside the channel in the backplate.
2. Change the size of the band by sliding
the links in or out of the stainless steel
backplate. For extra small users you can
cut off excess links with cutters.
3. Lock the links into place by pulling
down on the band, seating the band
securely over the lip on the edge of the
backplate.
4. Test the wrist strap system to be sure of
proper electrical resistance and skin
contact. Use the procedure described
under “Testing” section on reverse side.
Hook and Loop Wrist Strap
This wristband consists of a hook and loop
band with a D-ring buckle, a conductive
strip for static charge dissipation, and a
4mm snap stud. The D-ring enables the
wearer to cinch the band for a secure fit.
The band will adjust to fit any size wrist.
Contact with the wearer is established
through a conductive teflon tab sewn to the
inside of the band.
1. Attach wrist
strap on wrist
so that the
black
conductive
band makes
contact with skin.
2. Pull strap through D-ring and
cinch the band for a snug fit.
3. Test the wrist strap system to be sure of
proper electrical resistance and skin
contact. Use the procedure described
under "Testing The Wrist Strap" on page 1.
Note: Desco wrist straps and coil cords are UL
Listed for safety. However, this product is not
recommended for use on equipment with
operating voltage exceeding 250 VAC.
CAUTION: The ESD Series is for electrostatic
control. It will not reduce or increase your risk of
receiving electric shock when using or working
on electrical equipment. Follow the same
precautions you would use without wrist straps,
including:
• Make certain that equipment having a
• Make certain that you are not in contact with
Limited Warranty
Desco expressly warrants that for a period of one (1) year from
the date of purchase, Desco wrist strap components will be
free of defects in material (parts) and workmanship (labor).
Within the warranty period, the product will be tested, repaired,
or replaced at Desco’s option, free of charge. Call our
Customer Service Department at 909-627-8178 (Chino, CA) or
781-821-8370 (Canton, MA) for a Return Material Authorization
(RMA) and proper shipping instructions and address. Include a
copy of your original packing slip, invoice, or other proof of
purchase date. Any unit under warranty should be shipped
prepaid to the Desco factory. Warranty repairs will take
approximately two weeks.
If your unit is out of warranty, call Customer Service at 909-
627-8178 (Chino, CA) or 781-821-8370 (Canton, MA) for a
Return Material Authorization (RMA) and proper shipping
instructions and address. Ship your unit freight prepaid. Desco
will quote repair charges necessary to bring your unit up to
factory standards.
Warranty Exclusions
THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU
OF ALL OTHER PRODUCT WARRANTIES, EXPRESSED
AND IMPLIED, INCLUDING MERCHANT- ABILITY AND
FITNESS FOR A PARTICULAR PURPOSE WHICH ARE
SPECIFICALLY DISCLAIMED. The express warranty will not
apply to defects or damage due to accidents, neglect, misuse,
alterations, operator error, or failure to properly maintain, clean
or repair products.
Limit of Liability
In no event will Desco or any seller be responsible or liable for
any injury, loss or damage, direct or consequential, arising out
of the use of or the inability to use the product. Before using,
users shall determine the suitability of the product for their
intended use, and users assume all risk and liability
whatsoever in connection therewith.
grounding type plug is properly grounded.
grounded objects other than through the ESD
Series.
© 2008 DESCO INDUSTRIES INC.
Employee Owned