767B00201 C&K Components, 767B00201 Datasheet - Page 5

• Manufacturer Part Number: 767B00201
• Description: HDWR STOP RING FOR A ROTARY SW
• Manufacturer: C&K Components
• Type: Locking Ring, 13.72 mm Diameterr
• Series: Ar

Specifications of 767B00201

• Accessory Type: Stop Ring
• Illumination: Not Illuminated
• Mounting Style: Panel
• For Use With/related Products: A Series
• For Use With: A40303RNCQK - ROTARY 4P 3POS SILVERA4303RNCQR - ROTARY 3POS SILVER M10 X .75A112-03-R-S-C-Q - SWITCH ROTARY SP 12 POSA12515RNZQ - ROTARY SWITCH SP 8 POS 45 DEGREECKN9487 - SWITCH ROTARY .5" 90DEG SP 2POSCKN10206 - SWITCH ROTARY DP-4POS .375"A10415RSMCGE - SWITCH ROTARY 4POS 1POLE PC MNTCKN6043 - SWITCH ROTARY 3P 4POS 2.5A SLDCKN6042 - SWITCH ROTARY SP 12POS 2.5A PCBA11205RNZQ - SWITCH ROTARY SP 12POS 2.5A PCBCKN9488 - SWITCH ROTARY .5" 30 DEG 6POSA20303RNMCQ - SWITCH ROTARY DP PC MNT 3POSA12515RNZG - SWITCH ROTARY SOLDER 8POSCKN10089 - SWITCH ROTARY SP SLD LUG 8POSCKC7008 - SWITCH ROTARY 4P 3POS EYELETCKC7007 - SWITCH ROTARY 4P 3POS PC MNTCKC7006 - SWITCH ROTARY 3P 4POS EYELETCKC7005 - SWITCH ROTARY 3P 4POS PC MNTCKC7004 - SWITCH ROTARY 2P 6POS EYELETCKC7003 - SWITCH ROTARY 2P 6POS PC MNTCKC7002 - SWITCH ROTARY SP 12POS EYELETCKC7001 - SWITCH ROTARY SP 12POS PC MNTA206-S1-RN-CQ - SWITCH ROTARY DP PCMNT 6POS 2.5A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: *767B00201; 767B00201; CKN9486

Setting Stops on A112 and A125 Models
The number of switch positions is adjustable on A112
and A125 models only by means of a stop ring provided
with each switch. The number of positions is pre-set on
all other models and the stop ring is factory installed.
Soldering, Cleaning and Assembly Instructions for ‘MC’ Termination Option
Soldering
1. Insert switch base only into PC board.
2. Do not bend terminals.
3. Wave soldering recommended at
4. Hand solder at 500F, 10 sec.
Switch Assembly
1. Hold housing/shaft assembly by housing. Remove
2. Do not push on switch shaft. Detent mechanism will
3. While holding switch housing, align locating tab on
4. Push firmly on housing until latches snap in place.
5. Remove clip from shaft and discard. Assembly is
Stop ring
PART NO.
767B00201
Material: Brass
Finish: Nickel plated
NONE
500F solder temperature.
max./terminal.
protective cap by squeezing tabs and discard. (FIG. 1)
come apart.
base with notch on housing and engage 4 housing
latches in slots on base. (FIG. 2)
complete. (FIG. 3)
NO SEAL
E
EPOXY SEAL
FUNCTION
AVAILABLE HARDWARE
F
SPLASHPROOF BUSHING SEAL
K–7
Cleaning
1. Flux clean using vapor degreaser and forced
2. Do not allow switch base to ‘trap’ fluids.
3. Freon TMC, TF or Methylene Chloride give
To set stops: Turn shaft fully counter-clockwise and
insert stop ring tab in desired hole. Install lockwasher
and nut to retain stop ring for both PC and panel
mounting. Switch without stop ring has 12 positions.
rinse or triple bath method.
excellent results.
SPLASHPROOF
BUSHING SEAL
(FIG. 1)
1-4 Pole Rotary Switches
REMOVABLE CLIP
K
EPOXY & SPLASHPROOF BUSHING SEAL
Specifications and dimensions subject to change
(FIG. 2)
www.ck-components.com
LOCATING
Dimensions are shown: mm
STANDOFF
A Series
TAB
(FIG. 3)
K