IS-C0203-F-E NKK Switches, IS-C0203-F-E Datasheet - Page 4
![SMARTSWITCH CONTROLLER LCD](/photos/14/58/145804/is-c0203-f-e_sml.jpg)
IS-C0203-F-E
Manufacturer Part Number
IS-C0203-F-E
Description
SMARTSWITCH CONTROLLER LCD
Manufacturer
NKK Switches
Specifications of IS-C0203-F-E
Accessory Type
Controller
Description/function
SMARTSWITCH Development Kit
For Use With/related Products
SmartSwitch™ Switches
For Use With
360-2345 - SWITCH COMPACT LCD 64X32 RGB360-2343 - SWITCH LCD 64X32 RGB360-2341 - DISPLAY LCD 64X32IS01BCEF - SMARTDISPLAY SUPER YEL/GRN LEDIS01BCE - SMARTDISPLAY SUPER YELLOW LEDIS15SBFP4B - SMARTSWITCH COMPACT WHITE LEDIS15SBCP4EF - SMARTSWITCH COMPACT YEL/GRN LEDIS15SACP4CF - SMARTSWITCH COMPACT RED/GRN LEDIS15ABFP4B - SMARTSWITCH STD BLK W/WHITE LEDIS15ABDP4B - SMARTSWITCH STD BLU W/WHITE LEDIS15ABDP4EG - SMARTSWITCH STD YELLOW/BLUE LEDIS15ABDP4E - SMARTSWITCH STD BLUE W/YEL LEDIS15ABCP4EF - SMARTSWITCH STD YEL/GRN LEDIS15ABCP4E - SMARTSWITCH STD LED YELLOWIS15AACP4CF - SMARTSWITCH STD YEL RED/GRN LED360-2334 - SMARTDISPLAY RED/GREEN/BLUE360-2333 - SMARTDISPLAY SUPER RED/GREEN LED360-2332 - SMARTSWITCH STANDARD RED/GRN/BLU360-2331 - SMARTSWITCH COMPACT RED/GRN/BLU360-2330 - SMARTSWITCH STD RED/GRN LED360-2329 - SMARTSWITCH COMPACT RED/GRN LED
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
360-2425
7850 East Gelding Drive • Scottsdale, AZ 85260-3420
4. Operational Overview
Power-up Sequence:
Upon power up, the controller checks the position of the Mode Select Switch. The switch position has to match
the logic board/switches connected. The “High res” position will work only for LCD 64x32 switches/displays
while the “Standard res” position will work only for LCD 36x24 switches/displays.
Note: Setting the switch to a different setting than the Logic Board type may damage the assembly.
LED Brightness Adjustment Mode:
The controller will then allow the backlight brightness to be adjusted. Press the left hand switch to make both
LED modules dimmer. Press the right hand switch to make both LED modules brighter.
Main Operational Mode:
After a few seconds of user inactivity the controller will move into the main operations mode where the switch
on the left displays the image at the user’s first preset address. The right hand switch will display the image at
the user’s second preset address. The controller will then respond to a switch actuation or a timer expiration as
set by the user preset attributes.
Addresses:
A one byte value ranging from 01H to FFH representing the 255 memory.
Attribute Block for 64x32 Resolution Switches
IS-Dev Kit-5 and IS-Dev Kit-6 Users Manual A.doc
Toll Free 1.877.2BUYNKK (877.228.9655) • Phone 480.991.0942 • Fax 480.998.1435
IS-Dev Kit-5 and IS-Dev Kit-6 Users
A block of 8 bytes.
Byte
www.nkkswitches.com • Email engineering@nkkswitches.com
1
2
3
4
5
6
7
8
Address for LCD Module #1
when switch is pressed.
Address for LCD Module #2
when switch is pressed
Address for LCD Module #1
when the timer is expired.
Address for LCD Module #2
when the timer is expired.
Value for TIMER 1
Value for TIMER 2
LED CODE for on cycle
LED CODE for off cycle
Manual
Description
Page 4 of 24
1209