AT3024H NKK Switches, AT3024H Datasheet

SWITCH SQUARE CAP/GRAY 12MM

AT3024H

Manufacturer Part Number
AT3024H
Description
SWITCH SQUARE CAP/GRAY 12MM
Manufacturer
NKK Switches
Series
NP01r
Type
Cap, Square Solidr
Datasheets

Specifications of AT3024H

Switch Type
Pushbutton
Shape
Square
Color
Gray
Illumination
Non-Illuminated
Mounting Type
Snap Fit
Size
12.00mm L x 12.00mm W x 10.20mm H
Height
10.2 mm
Length
12 mm
Mounting Style
SMD/SMT
Termination Style
Snap In
Width
12 mm
Body Style
12 mm Square Cap
Material, Lens
Polycarbonate Resin
For Use With/related Products
NP01 Series
For Use With
NP0115HG03NN - SW PB SPST-NO SQ NON-ILLUMNP0115AG03NN - SW PB SPST-NO SQ NON-ILLUM
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
D
Series NP01
General
Electrical Capacity (Resistive Load)
Other Ratings
Materials & Finishes
Environmental Data
Installation
PCB Processing
Standards & Certifications
D72
Operating Temperature Range:
Nominal Operating Force:
Cap Installation Force:
Insulation Resistance:
Stationary Contacts:
Contact Resistance:
Dielectric Strength:
Movable Contact:
Switch Terminals:
Mechanical Life:
Electrical Life:
Logic Level:
Soldering:
Vibration:
Humidity:
Cleaning:
Actuator:
Stroke:
Shock:
Case:
Base:
Specifications
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
50 milliohms maximum
500 megohms minimum @ 250V DC
250V AC minimum between contacts for 1 minute minimum
500,000 operations minimum
500,000 operations minimum
Standard: 1.5
High: 2.5N
1.5mm (.059”)
Silicon rubber
Polycarbonate resin
Glass fiber reinforced polyamide resin
Silver over nickel with gold plating
Brass with gold plating
Brass with gold plating
–25°C through +50°C (–13°F through +122°F) for Illuminated
–25°C through +70°C (–13°F through +158°F) for Nonilluminated
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
5.0N maximum downward force on actuator
Wave Soldering: 270°C maximum @ 6 seconds maximum
Manual Soldering: 390°C maximum @ 4 seconds maximum
These devices are not process sealed. Hand clean locally using alcohol based solution.
The NP01 Series pushbuttons have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
±
0.8 Newtons
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
www.nkk.com
±
0.5 Newtons
Subminiature Smooth Actuation Pushbuttons

Related parts for AT3024H

AT3024H Summary of contents

Page 1

... These devices are not process sealed. Hand clean locally using alcohol based solution. The NP01 Series pushbuttons have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. ...

Page 2

Subminiature Smooth Actuation Pushbuttons Distinctive Characteristics Soft touch actuation achieved by mechanical silicon rubber structure. Distinct, long stroke of 1.5mm (.059”). Entire cap is fully illuminated with single or bicolor LED. Compact design with dimension of 12.5mm (.492”) from PC ...

Page 3

Series NP01 NP01 15 Pole & Circuit 15 SPST OFF (ON) G03 ( ) = Momentary Normally Open Contacts D Operating Force Standard (1.5N) A (Black Switch Body) High (2.5N) H (Gray Switch Body Operating Force OFF-Momentary ON ...

Page 4

Subminiature Smooth Actuation Pushbuttons Plunger Position ( ) = Momentary Normal Pole Model NP0115AG03L SP OFF NP0115HG03L Plunger Position ( ) = Momentary Normal Pole Model NP0115AG03N SP OFF NP0115HG03N A Standard Nominal Operating Force 1.5 0.5N ± Switch base ...

Page 5

Series NP01 LEDs are an integral part of the switch and not available separately. The electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the forward voltage, a ballast resistor is required. Single ...

Page 6

... Legends may be printed on the lens with laser etch, screen print or pad print methods. Epoxy based ink is recommended not use excessive force during installation on PC board or for cap installation. * NKK Switches can provide custom legends for caps. Contact factory for more information. Solid Color Cap for Nonilluminated (12.0) Sq ...

Related keywords