A22L-GW-6D-02A Omron, A22L-GW-6D-02A Datasheet - Page 24
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
A22L-GW-6D-02A
Manufacturer Part Number
A22L-GW-6D-02A
Description
SWITCH PB ILLUM RND ALT DPST WHT
Manufacturer
Omron
Series
A22r
Type
Illuminatedr
Specifications of A22L-GW-6D-02A
Circuit
DPST-NC
Switch Function
On-Off
Contact Rating @ Voltage
10A @ 110VAC
Actuator Type
Round, Clear Full Guard
Illumination Type, Color
LED, White
Illumination Voltage (nominal)
6 VDC
Mounting Type
Panel Mount
Termination Style
Screw Terminal
Pole Throw Configuration
DPST
Switch Configuration
N.C.
Actuator Style
Flush Round Button
Current Rating (max)
10A
Illumination Type
Led
Ac Voltage Rating (max)
440VVAC
Dc Voltage Rating (max)
380VVDC
Mechanical Life
5000000
Product Height (mm)
73.7mm
Product Depth (mm)
30mm
Operating Temp Range
-20C to 55C
Mounting Style
Panel
Terminal Type
Screw
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
A22LGW6D02A
A22LGW6D02AQ
A22LGW6D02AQ
Application
Mounting to the Panel
Panel Hole Dimensions
• Panel hole dimensions are given below.
• Recommended panel thickness: 1 to 5 mm.
• For 25-dia. holes, always use 25-dia. Rings. (Since the cutout
• If outer surface treatment such as coating is performed for the
dimensions are large, IP65 cannot be guaranteed unless 25-dia.
Rings are used.)
panel, the panel dimensions after outer surface treatment must
meet the specified panel dimensions.
Not Using a Lock Ring
22.3
+0.4
0
22 dia.
Using a Lock Ring
3.2
+0.2
0
22.3
+0.4
0
25
+0.5
0
25 dia.
Matrix Installation
1. The following panel hole dimensions
2. The following panel hole dimensions
For 1. above:
For 2. above:
Note: 1. The above dimensions are the minimum dimensions for when the wires
Mounting the Operation Unit on the Panel
Pitches A and B between the centers of the mounting holes are as follows:
Type of crimp terminal
Bare crimp terminals
Crimp terminals with
insulating sheath
• Insert the Operation Unit (Pushbutton, etc.) from the front surface of the
• When using a Legend Plate Frame, put one rubber washer each
• Align the Lock Ring with the groove in the casing, then insert the
panel, insert the Lock Ring and the mounting nut from the terminal side,
then tighten the nut. Before tightening, check that the rubber washer is
present between the Pushbutton Unit and the panel.
between the Legend Plate Frame and the panel and between the
Operation Unit and the Legend Plate Frame. (One rubber washer
will be provided when one Legend Plate Frame is ordered.)
Lock Ring so that its edge is located on the panel side.
apply when Switch Unit and the
Standard-size Legend Plate Frame and
Lock Ring are mounted, and lead wires
are connected directly to the Switch
Block.
apply when the Large-size Legend Plate Frame is mounted, and
when crimp terminals are connected to the Switch Block terminals.
2. With pushbuttons of external dimensions greater than 30 mm, set the
described under Applicable Wire Size on page 23 are used. If a
different wires are used, the wiring dimensions may be different so
determine an appropriate pitch before setup.
pitch according to the dimensions. (When using matrix installation for
the A22-M@, mount with a pitch of 40 mm instead of 30 mm in the
diagram above.)
A22-10, A22-10S
A22-01, A22-01S
A22-20, A22-20S, A22-02
A22-02S, A22-11, A22-11S
Switch Blocks
A22-10, A22-10S
A22-01, A22-01S
A22-20, A22-20S, A22-02
A22-02S, A22-11, A22-11S
A22-10, A22-10S
A22-01, A22-01S
A22-20, A22-20S, A22-02
A22-02S, A22-11, A22-11S
Switch Blocks
30
30
45 mm min.
55 mm min.
51 mm min.
61 mm min.
60 mm min.
70 mm min.
A22
A
B
B
A
24