MB2411JW01-H NKK Switches, MB2411JW01-H Datasheet
MB2411JW01-H
Specifications of MB2411JW01-H
Related parts for MB2411JW01-H
MB2411JW01-H Summary of contents
Page 1
... Wirewrap terminals certified 125V AC or 0.4VA @ 28V maximum. Add “/C” to end of part number to order CSA mark on switch. C96 ) acceleration (tested in 6 right angled directions, with 3 shocks in each direction) 2 in) for double nut; 0.7Nm (6.0 lb in) for single nut • • www.nkk.com Snap-Action Pushbuttons ...
Page 2
... Antijamming design protects contacts from damage due to excessive downward force on the actuator. Compatible companions with M series toggles. Body, bushing, and footprint dimensions ideal for mounting MB2400 pushbuttons and M toggles next to one another. Stainless steel frame resists corrosion. Longer center solder lug terminal simplifies wiring and soldering. ...
Page 3
... F Green Top LED G Blue C Red H Gray E Yellow F Green DESCRIPTION FOR TYPICAL ORDERING EXAMPLE MB2411JW01-C-3A-CF Red Cap 1 Red LED 1 Green LED Snap-in Frame Black Bezel with 2 Round LEDs SPDT ON-(ON) Circuit Silver Contacts with 3-Amp Rating Solder Lug Terminals www.nkk.com LED 2 LEDs ...
Page 4
... Thk = (0.8) .425” 05 (10.8mm) Epoxy Seal .750” 06 (19.05mm) .964” 07 Thk = (0.8) (24.5mm) C110 Snap-Action Snap-in Mount Pushbuttons POLES & CIRCUITS Connected Terminals Down Normal Down (ON) 1-3 1-2 (ON) 1-3 4-6 1-2 4-5 MOUNTING FRAME Panel Cutout for Single Pole without Bezel (12 ...
Page 5
... Snap-Action Snap-in Mount Pushbuttons AT465 (11.5) Sq .453” (11.5mm) .453 Square Cap Material: Polycarbonate Finish: Glossy OPTIONAL SNAP-IN BEZELS & BEZEL COLORS 1 AT207 Bezel Material: Polycarbonate Finish: Glossy (15.6) Contact factory for matte .614 finish. AT208 Bezel 2 for AT070 LED Material: Polycarbonate (19 ...
Page 6
... If the source voltage is greater than the rated voltage of the LED, a ballast resistor must be connected in series with the LED. The ballast resistor calculation and more lamp detail are shown in the Supplement section. Solder Lug (18.0) .709 (12.2) .480 MB2411JW01-C C112 Snap-Action Snap-in Mount Pushbuttons LED COLORS & SPECIFICATIONS Bezel Orientation on Switch AT617 LED For Bezel AT212 (3 ...
Page 7
... MB2411JW01-C-2A-C .311 Solder Lug • AT212 Bezel 3 (13.0) .512 2 (14.0) .551 1 (2.0) .079 (7.9) MB2411JW01-C-3A-CF .311 Solder Lug • AT213 Bezel 6 3 (13.0) .512 5 2 (14.0) .551 4 1 (2.0) Typ .079 (4.8) .189 (12.7) MB2461JW01-C-4A-CF .500 C C113 ...
Page 8
... Series MB2400 NKK Switches can provide custom legends for caps. Contact factory for more information. C Recommended Print Method: Screen Print or Pad Print Epoxy based ink is recommended. C114 Snap-Action Snap-in Mount Pushbuttons LEGENDS Suggested Printable Area for Cap (9.98) Sq (0.76) Typ .393 ...