WR11AS NKK Switches, WR11AS Datasheet - Page 2
![SWITCH ROCKER SPST 15A SEALED](/photos/15/8/150808/wr11as_sml.jpg)
WR11AS
Manufacturer Part Number
WR11AS
Description
SWITCH ROCKER SPST 15A SEALED
Manufacturer
NKK Switches
Series
WRr
Type
Environmentally Sealed Rockersr
Specifications of WR11AS
Circuit
SPST
Switch Function
On-Off
Contact Rating @ Voltage
15A @ 125VAC
Illumination
Non-Illuminated
Mounting Type
Panel Mount, Snap-In
Termination Style
Solder Lug
Panel Cutout Dimensions
34.20mm x 17.20mm
Contact Form
SPST
Contact Rating
15 Amps at 125 VoltsAC, 250 VoltsAC, 30 VoltsDC
Actuator
Rocker
Color
Black
Mounting Style
Panel
Terminal Seal
Epoxy
Contact Plating
Tin
Features
Single unit construction of flange and outer housing gives added protection from environmental elements
Voltage Rating Ac
125 VoltsAC, 250 VoltsAC
Brand/series
WR Series
Color, Button
Black
Electrical Life
15000 Operations for Maintained Circuits, 10000 Operations (Min.) for Momentary Circuits
Material, Body
Polyphenylene Ether
Material, Contact
Silver Alloy Plus Copper with Silver Plating
Mechanical Life
30000 Operations (Min.)
Resistance, Contact
10 Milliohms (Max.)
Resistance, Insulation
200 Megohms (Min.) @ 500 VDC
Standards
UL, cUL Listed, VDE Approved, EN Conformity
Temperature, Operating, Maximum
85 °C
Temperature, Operating, Minimum
-25 °C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Illumination Type, Color
-
Illumination Voltage (nominal)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
360-1507
General Specifi cations
NKK Switches • email: sales@nkkswitches.com • Phone (480) 991- 0942 • Fax (480) 998-1435 • www.nkkswitches.com
R
Electrical Capacity (Resistive Load)
Other Ratings
Materials & Finishes
Environmental Data
Installation
Standards & Certifications
R
Cover for Wire Lead Models:
D E
V
Wiring Material Standards:
Flammability Standards:
Operating Temp Range:
Soldering Time & Temp:
Insulation Resistance:
Stationary Contacts:
Movable Contactor:
Contact Resistance:
Dielectric Strength:
Behind Panel Seal:
Movable Contacts:
Wire Lead Covers:
C-UL Recognized:
Front Panel Seal:
Mechanical Life:
Angle of Throw:
UL Recognized:
VDE Approved:
EN Conformity:
Outer Housing:
Flange Gasket:
Electrical Life:
Power Level:
Inner Case:
Terminals:
Vibration:
Humidity:
Rocker:
Shock:
15A @ 125/250V AC or 15A @ 30V DC
10 milliohms maximum for solder lug & screw terminal models;
30 milliohms maximum for wire lead terminal models
200 megohms minimum @ 500V DC
1,250V AC minimum between contacts for 1 minute minimum;
3,750V AC minimum between contacts & case for 1 minute minimum
30,000 operations minimum
15,000 operations minimum for maintained circuits &
10,000 operations minimum for momentary circuits
24°
Polyphenylene ether
Polyamide (UL94V-0)
Melamine (UL94V-0)
Glass fi ber reinforced polyamide (UL94V-0)
Nitrile butadiene rubber
Brass with silver plating
Silver alloy plus copper with silver plating
Silver alloy plus copper with silver plating
Copper with tin plating for solder lug & wire lead; brass with silver plating for screw lug
Heat resistant polyvinyl chloride (Leads are AWG 14)
–25°C through +85°C (–13°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
IP67 of IEC60529, dust tight & water protected during temporary immersion for all models
IP60 of IEC60529, dust tight but not water protected for solder lug & screw terminal models
IP67 of IEC60529, dust tight & water protected during temporary immersion
for wire lead models
4 seconds maximum @ 410°C maximum for manual soldering
UL94V-0 outer housing, inner case, & outer cover on wire lead models
All models recognized at 15A @ 125/250V AC & 15A @ 30V DC; UL File No. WOYR2.E44145.
Add “/U” to end of part number to order UL mark on switch.
All models recognized at 15A @ 125/250V AC & 15A @ 30V DC; UL File No. WOYR8.E44145.
Add “/UC” to end of part number to order C-UL mark on switch.
All models approved at 15A @ 250V AC; VDE License No. 126501.
Add “/V” to end of part number to order VDE mark on switch.
WT11 & WT12 models meet European Norm for 3mm contact gap to prevent contact welds;
EN No. 61058-1
UL AWM 1015 Recognized at Flammability VW-1;
Temperature Range –20°C ~ +105°C; Maximum Load 600V; AWG 14.
CSA TEW 105 Certifi ed at Temperature Range –20°C ~ +105°C; Maximum Load 600V
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Environmentally Sealed Rockers
Series WR
3-05