SS-5GL2T Omron, SS-5GL2T Datasheet
SS-5GL2T
Specifications of SS-5GL2T
SS5GL2T
SW873
Available stocks
Related parts for SS-5GL2T
SS-5GL2T Summary of contents
Page 1
... Wide switching capacity range from microvoltage/current loads ( VDC to high-capacity loads 10 250 VAC) • Standard operating force, low force or super-low force models available • RoHS Compliant Ordering Information I Standard Type Microvoltage/microcurrent load 0.1 A max. (Bifurcated crossbar contacts) Contact Actuator OF Pin plunger 150 g ...
Page 2
... SS-5-F SS-5-FT SS-5 SS-5T SS-5GL-F SS-5GL-FT SS-5GL SS-5GLT SS-5GL13-F SS-5GL13-FT SS-5GL13 SS-5GL13T SS-5GL14-F SS-5GL14-FT SS-5GL14 SS-5GL14T SS-5GL2-F SS-5GL2-FT SS-5GL2 SS-5GL2T Soldered Tab (#110) terminal terminal SS-10 SS-10T SS-10GL SS-10GLT SS-10GL13 SS-10GL13T SS-10GL14 — SS-10GL2 SS-10GL2T SS 1023 Snap Action Switch ...
Page 3
... Service life Mechanical Electrical Weight Note: 1. SS-10 series only. 2. 50,000 operations minimum for the SS-10 series. 3. Applies to the pin plunger type (at the pin plunger of the lever type million operations for the SS-10 series. 5. Data shown are of initial value. I Operating Characteristics Part number ...
Page 4
... SS-10 series must have a power factor of 0.75 min. 3. Lamp load has an inrush current of 10 times the steady-state current 4. Motor load has an inrush current of 6 times the steady-state current the switch is used circuit and is subjected to inrush current or surge, connect a surge suppressor across the switch. SS-10GL13 SS-01GL14-E ...
Page 5
... Sealed lead wire terminal models have color coded leads. * Consult Omron for SPST-NC and SPST-NO contact form types ordering information. I Approvals UL (File No. E41515), CSA (File No. LR21642), SS-5/SS-10: EN conforms 61058-1 Type SS-10 series SS-5 series SS-01 series VDE (File No. 5861-3221) ...
Page 6
... Engineering Data I Mechanical service life Standard type (SS-5, SS-10 series) I Electrical service life Standard type (SS-5 series) Snap Action Switch SS 1027 ...
Page 7
... SS-5GL14 (-F) SS-10GL14 Note: 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. 2. Straight vertical PCB terminal models are shown above. Soldered terminal, Tab (#110) terminal, lead wire terminal, PCB terminal parallel to left and PCB terminal parallel to right are shown in the Terminals section. ...
Page 8
... I Hinge Roller Lever SS-01GL2 (-E, -F) SS-5GL2 (-F) SS-10GL2 Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. I Mounting holes Standard types Mounting holes below are for reference only Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. SS 1029 Snap Action Switch ...
Page 9
... Unit: mm (inch) I Terminals General-Purpose Type PCB terminal, straight vertical (D) PCB terminal, parallel to left (D1) Note: Thickness of all the terminals is 0.5 mm. Soldered terminal (blank) SS 1030 Snap Action Switch PCB terminal, parallel to right (D2) Quick-connect tab (#110) terminal (T) ...
Page 10
... MEMO SS 1031 Snap Action Switch ...
Page 11
... Seller is a party) which arises or is alleged to arise from Buyer's acts or omissions under these Terms or in any way with respect to the Products. Without limiting the foregoing, Buyer (at ...
Page 12
... However, some specifica- tions of the Product may be changed without any notice. When in doubt, spe- cial part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Seller representative at any time to con- firm actual specifications of purchased Product ...