HL-5030G Omron, HL-5030G Datasheet - Page 8

• Manufacturer Part Number: HL-5030G
• Description: SWITCH LIMIT ADJUSTBL ROLLR LEVR
• Manufacturer: Omron
• Series: HL-5000r
• Type: Limit Switchr

Specifications of HL-5030G

• Circuit: DPST (1-NO, 1-NC)
• Switch Function: On-Mom, Off-Mom
• Contact Rating @ Voltage: 5A @ 125VAC
• Actuator Type: Lever, Roller
• Mounting Type: Chassis Mount
• Termination Style: Screw Terminal
• Operating Force: 735gf
• Actuator Style: Adjustable Roller Lever
• Operating Force Max: 7.35N
• Contact Voltage Ac Max: 250V
• Contact Voltage Dc Max: 250V
• Contact Current Ac Max: 5A
• Contact Current Dc Max: 5A
• Switch Function Configuration: N.O./N.C.
• Current Rating (max): 5A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: HL5030G

Precautions
Refer to the “Precautions for All Switches” on CD.
Wiring
Wiring Procedure
1. Loosen the cover mounting screws and remove the cover.
2. Disconnect the rubber connector from the box conduit and press-
3. After inserting the solderless terminal into the Switch, tighten the
Applicable Lead Wires
Note: Do not use wires containing silicone, otherwise a contact failure may result.
Applicable Solderless Terminal
The following solderless terminals are available. Do not use fork or any other type of terminals, otherwise an accidental disconnection resulting in
a ground fault may result.
Mounting
To mount the Limit Switch securely, be sure to use two M5 Allen-
head bolts and washers. The tightening torque applied to each bolt is
4.90 to 5.88 N·m. To mount the Limit Switch more securely, use two
M5 screw holes on the rear panel and rear holes for positioning if the
model is the HL-5@@@G-Series Limit Switches.
Mounting holes
Only the HL-5@@@G has M5 x 0.8 screw holes on the rear side.
Others
Do not use the Limit Switch outdoors, otherwise the Limit Switch will
become damaged by rust or ozone.
The Limit Switch is not suitable in places exposed to the spray of
rainwater, seawater, or oily water. Consult your OMRON representa-
tive for models resisting rainwater, seawater, and oily water.
K-12
Vinyl cabtire cord (VCTF)
Vinyl cabtire cable (VCT)
600-V vinyl-insulated sheath cable
Fig. 1
10 max.
fit a solderless terminal. The following solderless terminals are
available.
terminal screws securely.
Correct Use
6.4 max.
General-purpose Limit Switch
Two, M5 screws or 5.2-dia. holes (located
diagonally for securing the front side)
Wire name
3.0 to 3.7 dia.
Two, 5.2-dia. holes (located
diagonally for securing the rear side)
Bare terminal
Fig. 2
10 max.
2
3
4
2
2
Number of conductors
6.4 max.
HL-5000
3.0 to 3.7 dia.
Fig. 3
14 max.
4. After wiring the Limit Switch, insert the rubber connector into the
5. Tighten the three mounting screws evenly. The optimum tighten-
If high-sealing performance is required along with shielded wiring or
conduit wiring, use the D4C or WL.
0.75 mm
0.75 mm
1 dia./1.2 dia./1.6 dia.
groove of the box securely.
ing torque for each screw is 0.49 to 0.59 N·m.
6.4 max.
Applicable wire
Conductor size
2
2
Cover
3.0 to 3.7 dia.
Terminal with insulated grip
Terminal
Fig. 4
Round, 6 to 9 dia.
Flat, 9.4 max.
14 max.
Cover mounting screw
Rubber connector
External size
6.4 max.
3.0 to 3.7 dia.