468MP 3/4"X60YD 3M, 468MP 3/4"X60YD Datasheet - Page 5

• Manufacturer Part Number: 468MP 3/4"X60YD
• Description: TRANSFER TAPE 468MP 3/4" X 60YD
• Manufacturer: 3M
• Series: 486MPr

Specifications of 468MP 3/4"X60YD

• Tape Type: Adhesive Transfer Tape
• Adhesive: Acrylic, 200MP
• Backing, Carrier: Polycoated Kraft Liner
• Thickness: 0.0091" (9.1 mils, 0.230mm)
• Thickness - Adhesive: 0.0051" (5.1 mils, 0.130mm)
• Thickness - Backing, Carrier, Liner: 0.0040" (4.0 mils, 0.102mm)
• Width: 0.75" (19.05mm) 3/4"
• Length: 180' (55.0m) 60 yds
• Color: Clear
• Usage: Automotive
• Temperature Range: 70 ~ 100°F (21 ~ 38°C)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 00-021200-19336-1; 00021200193361; 02120019336; 3M9040; 468MP-3/4"X60YD; 468MP-3/4"X60YD; 70-0060-7812-8; 70006078128

3M
467MP • 468MP • 467MPF • 468MPF • 7952MP • 7955MP
7962MP • 7965MP • 9172MP • 9185MP • 9667MP • 9668MP
Electrical, Mechanical
and Thermal Properties
Specifications
™
High Performance Adhesive Transfer Tapes with Adhesive 200MP
Please specify 3M adhesive 200MP, 2 mil or 5 mil rather than the exact product
number based on the liner configuration. The converter will select the product with
the necessary liner configuration to meet the delivery requirements.
Coat weight
Face Adhesion
Back Adhesion
7
8
Note: The following technical information and data should be considered representative
Property
Insulation Resistance (test voltage = 100 VDC)
Dielectric Strength – (500 vac, rms [60 hz/sec])
Breakdown Voltage
Dielectric Constant (at 1 KHz)
Dissipation Factor
Tensile Lap Shear – Peak Load
Tensile Lap Shear – Peak Stress
Tensile Strength and Elongation
Thermal Conductivity
Coefficient of Thermal Expansion - first heat
The amount of adhesive supplied, for pressure-sensitive adhesives, is controlled by the
adhesive coat weight, not the adhesive caliper. Pressure-sensitive adhesives are
compressible which results in high error for caliper measurements. The caliper listed in the
Constructions section (page 1) has been calculated using a density of 1.012 g/cc (testing
caliper is not part of the standard release testing because of the error described.)
ASTM D3330, 15 minute dwell on stainless steel. For this adhesive family, the adhesion will be
much higher with longer dwells on stainless steel and other high surface energy materials
(please refer to the typical Physical Properties section in this document to see performance on
other materials after longer dwells).
Mil-I-46058C
ASTM D149-92
ASTM D 150-92
ASTM D1002-72
(0.5 square inch on #6061 aluminum)
ASTM D1002-72
ASTM D2370-82
(ASTM C 518, results listed are at 109°F)
ASTM D 696
or typical only and should not be used for specification purposes.
7
(grains/4" x 6")
(grams/ft
8
8
(exposed side)
ounces/inch
(liner side)
ounces/inch
2
)
- 5 -
- second heat
28 x 10
72 x 10
>1 x 10
0.17 watt/m-K
0.098 BTU-ft/
880 volts/mil
1,760 volts
30 minimum
30 minimum
5.4 ± 12%
ft
14 ± 12%
0.021
2 mil
2
3.40
-hr-F
2 mil
-5
-5
10
3M™ Adhesive 200MP
m/m/C
m/m/C
3M adhesive 200MP
ohms
92 x 10
-6 x 10
>1 x 10
0.18 watt/m-K
0.101 BTU-ft/
600 volts/mil
12.4 ± 12%
37 minimum
37 minimum
3,000 volts
32 ± 12%
109 PSI
1915%
ft
51 PSI
55 lbs.
0.022
5 mil
5 mil
2
4.06
-hr-F
-5
-5
10
m/m/C
m/m/C
ohms