SP6651AEU-L Exar Corporation, SP6651AEU-L Datasheet - Page 10

• Manufacturer Part Number: SP6651AEU-L
• Description: IC CONV SYNC BUCK 800MA 10MSOP
• Manufacturer: Exar Corporation
• Type: Step-Down (Buck)r
• Series: -r

Specifications of SP6651AEU-L

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 1 V ~ 5.5 V
• Current - Output: 800mA
• Voltage - Input: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 10-TFSOP, 10-MSOP (0.118", 3.00mm Width)
• Primary Input Voltage: 5.5V
• No. Of Outputs: 1
• Output Voltage: 5V
• Output Current: 800mA
• No. Of Pins: 10
• Operating Temperature Range: -40°C To +85°C
• Supply Voltage Range: 2.7V To 5.5V
• Mounting Style: SMD/SMT
• Frequency - Switching: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

For the typical SP6651A application circuit with
inductor size of 10µH, and K
SP6651A current ripple would be about 200mA,
driver latch and open the switch to prevent
inductor current reversal. This circuit along
with the on-timer puts the converter into PFM
mode and improves light load efficiency when
the load current is less than half the inductor
ripple current defined by K
Thermal Shutdown
The converter will open both power switches if
the die junction temperature rises above 140°C.
The die must cool down below 126°C before the
regulator is re-enabled. This feature protects the
SP6651A and surrounding circuitry from exces-
sive power dissipation due to fault conditions.
Shutdown/Enable Control
The D0, D1 pins 4,5 of the device are logic level
control pins that according to Table 1 shut down
the converter when both are a logic low, or
enables the converter when either are a logic
high. When the converter is shut down, the
power switches are opened and all circuit bias-
ing is extinguished leaving only junction leak-
age currents on supply pins 1 and 2. After pins
4 or 5 are brought high to enable the converter,
there is a turn on delay to allow the regulator
Date: 5/25/04
Inductor Selection
The SP6651A uses a specially adapted mini-
mum on-time control of regulation utilizing a
precision comparator and bandgap reference.
This adaptive minimum on-time control has the
advantage of setting a constant current ripple
for a given inductor size. From the operations
section it has been shown:
Inductor Current Ripple, I
SP6651A High Efficiency 800mA Synchronous Buck Regulator
ON
LR
ON
/L.
≈
of 2V*µsec, the
K
ON
L
10
circuitry to re-establish itself. Power conversion
begins with the assertion of the internal refer-
ence ready signal which occurs approximately
150µs after the enable signal is received.
Battery Low Indicator
The BLON function is a differential measure-
ment of (V
drain NMOS on pin 3 to sink current to ground
when (V
from pin 3 to V
battery low indicator. A low bandwidth com-
parator and 3% hysteresis filter the input voltage
ripple to prevent noisy transitions at the thresh
old. BLON is forced Low when in UVLO.
External Feedback Pin
The FB pin 6 is compared to an internal refer-
ence voltage of 0.8V to regulate the SP6651A
output. The output voltage can be externally
programmed within the range +1.0V to +5.0V
by tying a resistor from FB to ground and FB to
V
resistor selection information.
and would be fairly constant for different input and
output voltages, simplifying the selection of com-
ponents for the SP6651A power circuit. Other
inductor values could be selected, as shown in
Table 2 Components Selection. Using a larger
value than 10µH in an attempt to reduce output
voltage ripple would reduce inductor current ripple
and may not produce as stable an output ripple.
For larger inductors with the SP6651A, which
has a peak inductor current of 1.25A, most
15µH or 22µH inductors would have to be larger
physical sizes, limiting their use in small por-
table applications. Smaller values like 6.8µH
would more easily meet the 1.25A limit and
come in small case sizes, and the increased
OUT
THEORY OF OPERATION: Continued
(pin7). See the applications section for
IN
-V
IN
APPLICATION INFORMATION
OUT
-V
IN
OUT
) < 300mV. Tying a resistor
or V
) which causes the open
OUT
© Copyright 2004 Sipex Corporation
creates a logic level