025-0767-001 ITT Cannon, 025-0767-001 Datasheet - Page 79

• Manufacturer Part Number: 025-0767-001
• Description: RP CONDUCTIVE D/C 34 SHELL
• Manufacturer: ITT Cannon

Specifications of 025-0767-001

• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: I025-0767-001

Test Data
Dimensions shown in inch (mm)
Specifications and dimensions subject to change
www.ittcannon.com
MIL-C-83733
The following is a presentation of the certified
capabilities of Cannon's DPK, high performance,
rectangular, rack and panel series connectors with
respect to critical qualification performance and
design requirements of MIL-C-83733. The data
presented herein is a condensation of authentic
qualification test data extracted from the original
qualification reports on file at the ITT Cannon Test
Laboratory.
Test Description
Examination Of Product
visual Examination
Sample Preparation
Insulation Resistance - 25˚C
Withstanding Voltage - Sea Level
Withstanding Voltage - Altitude
Contact Resistance
Test or
Environment
Examination Of Product
visual Examination
Sample Preparation
Insulation Resistance - 25 C
Withstanding Voltage - Sea Level
Withstanding Voltage - Altitude
Contact Resistance
VISUAL
EXAMINATION
SAMPLE
PREPARATION
INSULATION RESISTANCE
[25 C (77 F)]
DIELECTRIC
WITHSTANDING
VOLTAGE (SEA LEVEL)
SALT SPRAY (CORROSION)
CONTACT RESISTANCE
[AT 25 C AND 200 C
(77 F AND 392 F)]
CONTACT SEPARATING FORCES
CONNECTOR MATING AND
UNMATING FORCES
CONTACT RETENTION
ENDURANCE (DURABILITY)
Assure compliance with:
Visual examination of qualification test specimens for completness,
workmanship, identification and /or other detrimental conditions.
MIL-W-16878/4A, 28 AWG (min. dia.) and 22 AWG (max. dia.) wire.
Daniels WA22A crimping tool. M22520/2-06 and M22520/2-09 contact
positioner for resp.22D size socket and pin. MS7495A22M insertion and
MS27495R22M removal tool.
Unmated condition. 50% of contact complement measured. Between adjacent
contact paris and each contact and connector shell.
Unmated condition. 50% of contact complement measured. Test voltage 1350
Vac/rms-60hz, applied between adjacent contact pairs and each contact and
connector shell.
Method 101, test condition B. (48 hours) unmated. Salt soultion 5% by
weight. S.G. 1.026 to 1.040 at 22.8 C-23.9 C (73 F-75 F). Solution pH6.5
to 7.2 and chamber temp 33.9 C to 36.1 C (93 F to 97 F).
Mated condition 20% of contact complement tested. Test circuit per Fig. 2
measured across points YY performed at 25 C and 200 C (77 F and 392 F).
100% of socket contact complement measured. Separating force measured
on steel test pin .0294 + _ .0001 (0.747 + _ 0.002) dia. insertion depth .205
(5.21) min. from insert face.
Mating dept, .390 (9.91) panel spacing. Total of 10 cycles mating and
unmatings. Forces measured on 10th cycle.
Unmated. 50% of contacts measured. 10.0 1bf applied to contact engaging
end. Zero reference at 2.0 1bf preload. Displacement measured under spec.
load.
Mating dept, .450 (11.43) panel spacing. Total of 500 cycles mating and
unmating at a rate of 300 cycles/hour maximum.
a) Applicable detail specifications and control drawings
b) Materials
c) Design and construction
d) Dimensional
e) Finish
f ) Product identification
g) Workmanship
Wire size
Contact/
22D/28
22D/22
Test Description
Contact Separating Forces
Connector Mating and Unmating Forces
Contact Retention
Endurance
Gold Plating Porosity
Temperature Life
Insulation Resistance - 200˚C
Special Requirments
Test Level or
The successful completion of the conducted qual-
ification program clearly demonstrates the compli-
ance of ITT Cannon, DPK series connectors and
contacts to meet or exceed the performance re-
quirements of MIL-C-83733.
Identification of Qualification Specimens
The DPK connectors listed below represent the
description and identification of the test specimens
Test Current
TABLE 1
Adc
1.5
5.0
79
TABLE ll
TEST PERFORMED
Compliance to applicable detail specification and
control drawings.
Visual examination acceptance.
Assemblies to conform with specified wiring and
termination requirements.
5.1 Gigohms minimum at 500 Vdc.
Electrification Time 120 secs. maximum.
No electrical breakdown, flashover or excessive
current leakage.Electrification 2 secs.
minimum.
Visual examination. No degradation of normal
connector functions.
Max. Voltage Drop (MV)
Separating Force (ounce-force)
Axial mating and unmating forces 175
pounds-force maximum.
Max. contact displacement under 10.0 1bf load
.011 (0.28) maximum.
Withstand 500 cycles of durability conditioning
without detrimental effects to function.
Test Description
Low Leve Contact Resistance
Thermal Shock
Crimp Potential Drop
Vibration (Random)
Physical Shock
Ozone Exposure
Fluid Immersion
Wire
Size
28
22
Min.
0.6
Parameters Limits
(77˚F)
25 C
14
8
Max.
4.9
(392˚F)
200 C
19
25
subjected to the qualification test sequence of
MIL-C-83733.
DPKA-G-131PC-7 (Receptacle) DPKB-G185PC-7 (Receptacle)
DPKA-G131SK-7 (Plug)
DPKA-G-131PC-7 (Receptacle) DPKB-G185PC-7 (Receptacle)
Table I below, lists the conducted tests executed in
accordance with the applicable test paragraphs of
MIL-C-83733, with the Test Level, Parrameter
Limits and Measured Values listed in Table 11.
No detrimental damage. Connectors fully functional.
Product submitted accompanied by Q.A.certifiates of compliance.
complied with the applicable acceptance requirements for qualification
testing.
No visible detection of any condition detrimental to normal function.
Qualification test specimens prepared and terminated in accordance
with specified wiring requirements. No difficulties encountered during
wiring operation.
Insul. res. range (ohms) (25 C) DPKA
Adj. Cont.
300G-1.0T
DPKB
400G-1.6T
(Ganged parallel test circuits)
No evidence of breakdown or flashover Leakage < _ .5mA. (Ganged
Parallel test circuits)
No detrimental corrosive attack on connector's surface finish or
contacts.
MV-Drop Range. (25˚C)
Separating force range (ounce-force)
Mating/Unmating Force (pound-force)
DPKA
DPKB
Forces obtained on 10th cycle.
Contact Displacement Range (inch)
DPKA
Pins
Sockets
DPKB
Pins
Sockets
Wire
Size
28
22
28
22
Test Description
Moisture Resistance
Altitude Immersion
Insert Retention
Corrosion
Analyses
DPKA Sep. Force
Service and Storage Life
Gases and Toxic or Corrosive Fumes
1.3-4.1
1.0-2.9
DPKB
Adc
1.5
5.0
1.5
5.0
Measured Values
or Comments
0.002-0.003
0.002-0.004
0.002-0.004
0.002-0.003
DPKA-G185SK-7 (Plug)
Mate
145
150
Cont./Shell
DPK
1.1T-1.8T
1.1T-20T
2.3-5.2
Range
6.3-10
16-21
(mV)
9-17
Avg. Force
(200 C)
2.4
2.0
Unmated
0.0027
0.0031
0.0027
0.0026
Avg.
34
72
(mV)
Avg.
11.8
17.8
3.8
8.2