MCP4441-103E/ML Microchip Technology, MCP4441-103E/ML Datasheet - Page 16
![IC DGTL POT 129TAPS QUAD 20QFN](/photos/18/99/189944/4388371_sml.jpg)
MCP4441-103E/ML
Manufacturer Part Number
MCP4441-103E/ML
Description
IC DGTL POT 129TAPS QUAD 20QFN
Manufacturer
Microchip Technology
Datasheet
1.MCP4441-103EML.pdf
(100 pages)
Specifications of MCP4441-103E/ML
Taps
129
Resistance (ohms)
10K
Number Of Circuits
4
Temperature Coefficient
150 ppm/°C Typical
Memory Type
Non-Volatile
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
20-VFQFN Exposed Pad
End To End Resistance
10kohm
Track Taper
Linear
Resistance Tolerance
± 20%
No. Of Steps
129
Supply Voltage Range
2.7V To 5.5V
Control Interface
I2C
No. Of Pots
Quad
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP4441-103E/ML
Manufacturer:
Microchip Technology
Quantity:
135
MCP444X/446X
TABLE 1-3:
DS22265A-page 16
I
Note 1:
2
Param.
C AC Characteristics
No.
107
109
110
2:
3:
4:
5:
6:
7:
As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions.
A fast-mode (400 kHz) I
requirement t
stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal,
it must output the next data bit to the SDA line
T
the SCL line is released.
The MCP44X1/MCP44X2 device must provide a data hold time to bridge the undefined part between V
and V
must be tested in order to ensure that the output data will meet the setup and hold specifications for the
receiving device.
Use Cb in pF for the calculations.
Not Tested.
A Master Transmitter must provide a delay to ensure that difference between SDA and SCL fall times do
not unintentionally create a Start or Stop condition.
Ensured by the T
R
T
SU:DAT
T
Sym
max.+t
T
T
BUF
AA
SP
IL
I
2
of the falling edge of the SCL signal. This specification is not a part of the I
C BUS DATA REQUIREMENTS (SLAVE MODE) (CONTINUED)
SU;DAT
Characteristic
Bus free time
Input filter spike
suppression
(SDA and SCL)
Data input setup
SU;DAT
Output valid
from clock
AA
= 1000 + 250 = 1250 ns (according to the standard-mode I
time
3.4 MHz specification test.
≥ 250 ns must then be met. This will automatically be the case if the device does not
2
C-bus device can be used in a standard-mode (100 kHz) I
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
Operating Voltage V
100 kHz mode
400 kHz mode
1.7 MHz mode
3.4 MHz mode
100 kHz mode
400 kHz mode
1.7 MHz mode
3.4 MHz mode
100 kHz mode
400 kHz mode
1.7 MHz mode
3.4 MHz mode
100 kHz mode
400 kHz mode
1.7 MHz mode
3.4 MHz mode
DD
4700
1300
N.A.
N.A.
range is described in
Min
250
100
10
10
—
—
—
—
—
—
—
—
—
–40°C ≤ T
3450
Max
900
150
310
150
50
50
10
10
—
—
—
—
—
—
—
—
A
≤ +125°C (Extended)
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
AC/DC characteristics
© 2010 Microchip Technology Inc.
2
C bus specification) before
Note 2
Note 1
Cb = 100 pF,
Note
Cb = 400 pF,
Note
Cb = 100 pF,
Time the bus must be free
before a new transmission
can start
Philips Spec states N.A.
Spike suppression
Spike suppression
2
2
C specification, but
C-bus system, but the
1,
1,
Conditions
Note 7
Note 5
Note 1
IH