AT32UC3C0512C-ALUT Atmel, AT32UC3C0512C-ALUT Datasheet - Page 76

• Manufacturer Part Number: AT32UC3C0512C-ALUT
• Description: IC MCU AVR32 512K FLASH 144LQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3C0512C-ALUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 123
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 16x12b, D/A 4x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LFQFP
• Data Bus Width: 32 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

10.1.5
10.1.6
10.1.7
32117A–10/2010
TWI
USBC
WDT
3. SPI data transfer hangs with CSR0.CSAAT==1 and MR.MODFDIS==0
4. Disabling SPI has no effect on the SR.TDRE bit
1. TWIM SMBAL polarity is wrong
1. UPINRQx.INRQ field is limited to 8-bits
1. Clearing the Watchdog Timer (WDT) counter in second half of timeout period will
W h e n m u l t i p l e c h i p s e l e c t s a r e i n u s e , i f o n e o f t h e b a u d r a t e s i s e q u a l t o 1
(CSRn.SCBR==1) and one of the others is not equal to 1, and CSRn.CPOL==1 and
CSRn.NCPHA==0, an additional pulse will be generated on SCK.
Fix/Workaround
When multiple chip selects are in use, if one of the baudrates is equal to 1, the others must
also be equal to 1 if CSRn.CPOL==1 and CSRn.NCPHA==0.
When CSR0.CSAAT==1 and mode fault detection is enabled (MR.MODFDIS==0), the SPI
module will not start a data transfer.
Fix/Workaround
Disable mode fault detection by writing a one to MR.MODFDIS.
Disabling SPI has no effect on SR.TDRE whereas the write data command is filtered when
SPI is disabled. This means that as soon as the SPI is disabled it becomes impossible to
reset the SR.TDRE bit by writing to TDR. So if the SPI is disabled during a PDCA transfer,
the PDCA will continue to write data to TDR (as SR.TDRE stays high) until its buffer is
empty, and all data written after the disable command is lost.
Fix/Workaround
Disable the PDCA, add 2 NOP (minimum), and disable the SPI. To continue the transfer,
enable the SPI and the PDCA.
The SMBAL signal in the TWIM is active high instead of active low.
Fix/Workaround
Use an external inverter to invert the signal going into the TWIM. When using both TWIM
and TWIS on the same pins, the SMBAL cannot be used.
In Host mode, when using the UPINRQx.INRQ feature together with the multi-packet mode
to launch a finite number of packet among multi-packet, the multi-packet size (located in the
descriptor table) is limited to the UPINRQx.INRQ value multiply by the pipe size.
Fix/Workaround
UPINRQx.INRQ value shall be less than the number of configured multi-packet.
issue a Watchdog reset
If the WDT counter is cleared in the second half of the timeout period, the WDT will immedi-
ately issue a Watchdog reset.
Fix/Workaround
Use twice as long timeout period as needed and clear the WDT counter within the first half
of the timeout period. If the WDT counter is cleared after the first half of the timeout period,
you will get a Watchdog reset immediately. If the WDT counter is not cleared at all, the time
before the reset will be twice as long as needed.
AT32UC3C
76