MC9S08MM64CLH Freescale Semiconductor, MC9S08MM64CLH Datasheet - Page 19
![IC MCU 8BIT 32K FLASH 64LQFP](/photos/37/62/376286/mc9s_sml.jpg)
MC9S08MM64CLH
Manufacturer Part Number
MC9S08MM64CLH
Description
IC MCU 8BIT 32K FLASH 64LQFP
Manufacturer
Freescale Semiconductor
Series
HCS08r
Datasheet
1.MC9S08MM128CMB.pdf
(52 pages)
Specifications of MC9S08MM64CLH
Core Processor
HCS08
Core Size
8-Bit
Speed
48MHz
Connectivity
I²C, SCI, SPI, USB
Peripherals
LVD, POR, PWM, WDT
Number Of I /o
33
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
12K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Data Converters
A/D 6x16b, D/A 1x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-LQFP
Processor Series
S08MM
Core
HCS08
Data Bus Width
8 bit
Data Ram Size
12 KB
Maximum Clock Frequency
48 MHz
Operating Supply Voltage
- 0.3 V to + 3.8 V
Maximum Operating Temperature
+ 105 C
3rd Party Development Tools
EWS08
Development Tools By Supplier
TWR-SER, TWR-ELEV, TWR-S08MM128-KIT, TWR-SENSOR-PAK, TWR-MCF51MM-KIT, TWR-LCD
Minimum Operating Temperature
- 40 C
On-chip Adc
16 bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MC9S08MM64CLH
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Freescale Semiconductor
Freescale reserves the right to change the detail specifications as may be required to permit improvements in the design of its products.
1
2
3
4
5
6
7
8
9
10
11
Num Symbol
20
21
22
23
Typical values are measured at 25C. Characterized, not tested
As the supply voltage rises, the LVD circuit will hold the MCU in reset until the supply has risen above V
Does not include analog module pins. Dedicated analog pins should not be pulled to V
floating when not used to reduce current leakage.
Measured with V
All functional non-supply pins are internally clamped to V
Input must be current limited to the value specified. To determine the value of the required current-limiting resistor,
calculate resistance values for positive and negative clamp voltages, then use the larger of the two values.
Power supply must maintain regulation within operating V
current conditions. If positive injection current (V
and could result in external power supply going out of regulation. Ensure external V
than maximum injection current. This will be the greatest risk when the MCU is not consuming power. Examples are:
if no system clock is present, or if clock rate is very low (which would reduce overall power consumption).
Maximum is highest voltage that POR is guaranteed.
Run at 1 MHz bus frequency
Low voltage detection and warning limits measured at 1 MHz bus frequency.
Factory trimmed at V
V
V
V
V
LVWH
LVWL
hys
BG
Low-voltage
warning
threshold —
high range
Low-voltage
warning
threshold —
low range
Low-voltage inhibit reset/recover
hysteresis
Bandgap Voltage Reference
In
= V
DD
DD
9
= 3.0 V, Temp = 25C
Characteristic
10
.
9
Table 9. DC Characteristics (Continued)
V
V
V
V
DD
DD
DD
DD
falling
rising
falling
rising
11
In
> V
DD
Condition
) is greater than I
SS
—
—
—
—
—
—
DD
and V
range during instantaneous and operating maximum
DD
except PTD1.
2.36
2.36
2.11
2.16
1.15
DD
Min
—
, the injection current may flow out of V
DD
Typ
2.46
2.46
2.16
2.23
1.17
50
load will shunt current greater
DD
1
or V
Electrical Characteristics
Max
2.56
2.56
2.22
2.27
1.18
SS
—
and should be left
Unit
mV
LVDL
V
V
V
V
V
.
C
C
P
P
P
P
P
DD
19