EXPANDIO-USB-SS Flexipanel, EXPANDIO-USB-SS Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
EXPANDIO-USB-SS
Manufacturer Part Number
EXPANDIO-USB-SS
Description
USB Interface IC Driver-free USB I/O- expander
Manufacturer
Flexipanel
Series
expandIO-USB™r
Datasheet
1.EXPANDIO-USB-PT-FS.pdf
(15 pages)
Specifications of EXPANDIO-USB-SS
Interface
USB
Number Of I /o
12
Interrupt Output
No
Frequency - Clock
375kHz
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
20-SSOP
Includes
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Delivery and Programming
In high volumes (5K+), expandIO-USB is available
reeled with your custom settings preloaded.
devices listed in table 9 are commonly stocked by
distributors.
USB-expandIO-SS may be supplied with an ID label, or
it may be identified with a red mark on the package.
Programming expandIO-USB
expandIO-USB may be programmed in-circuit provided
the programming signals PGC, PGD and Vpp are
protected against contention. In particular, note that the
Vpp line is subject to a voltage of up to 13V during
programming. Nothing else should be connected to this
input except via a 22k pull-up resistor.
Since the programming time is fast, no programming
socket is required for the TEAclipper. It may be leaned
against five plate-through holes as described in figure
10. In-circuit programming connections of some form
should always be provided, even if the device is
supplied pre-loaded, in order to facilitate firmware
upgrades.
Evaluation Board
expandIO-USB may be evaluated with the Firmware
Factory USB Products Eval Board (figure 11).
components which must be fitted are shown in table 10.
p11
Pin 1 indicated
by square pad
Part number
USB-expandIO-DIL
USB-expandIO-PT
USB-expandIO-SS
Figure 10. Recommended TEAclipper PCB connector
Table 9. Commonly stocked part numbers
Figure 9. HIDconfig.exe application
22-Nov-10
18F14K50
18LF2455
18LF4455
MCU
2.54mm spacing
USB Speed Package
Full
Full
Full
expandIO-USB
1mm hole dia
TQFP-44
SSOP-20
DIL-28
The
The
In addition, the prototyping area on the left may be used
to add components to which the expandIO-USB will
interface.
The printed circuit board integrates an edge connector
of USB Type A format. This may be plugged into a USB
extension cable.
The HIDconfig.exe application can be used to discover
and test the evaluation circuit prior to writing a software
application to do the task.
Licensing
This firmware is copyright Firmware Factory Ltd and
may only be used with permission. Licenses may be
purchased from HexWax Ltd. For preprogrammed reels,
contact Firmware Factory Ltd.
Development Kit
A firmware development kit is available for download
from www.hexwax.com containing the following files:
LED1, LED2
Additional components may be added for a more complete evaluation
Table 10. Evaluation Board minimum bill of materials
HW148-18
C2, C3
(Additional components added compared to table 8.)
Label
U2
D2
C4
C7
C8
R2
X1
Base controller data sheets (© Microchip
Technology Inc)
USB 2.0 Specification (© HP / Intel / Lucent /
Microsoft / NEC / Philips 2000)
UNI/O™ Bus Specification DS22076
(© Microchip Technology Inc)
HIDconfig.exe for in-factory customization of
expandIO-USB devices via the USB port.
Figure 11. USB Products Eval Board
expandIO-USB-28-FS-DIL
12MHz parallel cut crystal
Light emitting diode 5mm
100nF capacitor
470nF capacitor
10uF capacitor
22pF capacitor
Component
22k resistor
Wire link
www.firmwarefactory.com