GNM214R71E222MA01D Murata, GNM214R71E222MA01D Datasheet - Page 2
![Capacitor Arrays & Networks 4 Cap Array 0805 X7R 25V 2200pF](/photos/16/29/162963/c2eb4p01_sml.jpg)
GNM214R71E222MA01D
Manufacturer Part Number
GNM214R71E222MA01D
Description
Capacitor Arrays & Networks 4 Cap Array 0805 X7R 25V 2200pF
Manufacturer
Murata
Series
GNMr
Datasheet
1.GNM212R61A225ME16D.pdf
(4 pages)
Specifications of GNM214R71E222MA01D
Voltage Rating
25 Volts
Number Of Elements
4
Operating Temperature Range
- 55 C to + 125 C
Termination Style
SMD/SMT
Dimensions
2 mm L x 1.25 mm W x 0.6 mm H
Dissipation Factor Df
0.025
Product
Ceramic Capacitor Arrays
Capacitance
2200 pF
Tolerance
20 %
Temperature Coefficient
X7R
Package / Case
0805
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
GNM214R71E222MA01D
Manufacturer:
MURATA
Quantity:
640 000
Company:
Part Number:
GNM214R71E222MA01D
Manufacturer:
MURATA
Quantity:
240 000
No.
11
12
13
14
GNM Series Specifications and Test Method (1)
Continued from the preceding page.
Vibration
Resistance
Resistance to
Soldering Heat
Deflection
Solderability of
Termination
Item
Appearance
Capacitance
Q/D.F.
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
No defects or abnormalities
Within the specified tolerance
30pF min.: QU1000
30pF max.:
C: Nominal
No cracking or marking defects should occur.
75% of the terminations are to be soldered evenly and
continuously.
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T2.5%
(Whichever is
larger)
30pF min.: QU1000
30pF max.:
C: Nominal
More than 10,000MΩ or 500Ω · F (Whichever is smaller)
No failure
Compensating Type
#GNMpp4
Capacitance (pF)
Capacitance (pF)
Temperature
GNM0M2
GNM1M2
GNM212
GNM214
GNM314
QU400+20C
or T0.25pF
QU400+20C
Type
5.0
d
a
b
c
100
1.0
2.0T0.05
2.0T0.05
2.0T0.05
2.0T0.05
2.5T0.05
R7, R6: Within T7.5%
R7, R6
R7, R6
Char.
Char.
a
Specifications
Fig. 2
0.2T0.05
0.5T0.05
0.6T0.05
0.7T0.05
0.8T0.05
25V min.
25V min.
0.025
0.025
max.
max.
High Dielectric Type
#GNMpp2
b
5.0
0.035
0.035
d
max.
0.32T0.05
max.
a
b
16V
16V
0.2T0.05
0.5T0.05
0.3T0.05
0.4T0.05
c
c
100
1.0
0.035
0.035
max.
max.
10V
10V
0.25T0.05
0.32T0.05
0.5T0.05
0.2T0.05
0.4T0.05
t=0.8mm
(in mm)
d
max.
max.
6.3V
0.05
6.3V
0.05
Solder the capacitor to the test jig (glass epoxy board) in the
same manner and under the same conditions as (10). The
capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should
be traversed in approximately 1 minute. This motion should be
applied for a period of 2 hours in each of 3 mutually perpendic-
ular directions (total of 6 hours).
Solder the capacitor on the test jig (glass epoxy board) shown
in Fig. 2 using a eutectic solder.
Then apply a force in the direction shown in Fig. 3 for 5T1 sec.
The soldering should be done by the reflow method and should
be conducted with care so that the soldering is uniform and free
of defects such as heat shock.
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at
80 to 120°C for 10 to 30 seconds. After preheating, immerse in
eutectic solder solution for 2T0.5 seconds at 230T5°C or
Sn-3.0Ag-0.5Cu solder solution for 2T0.5 seconds at 245T5°C.
Preheat the capacitor at 120 to 150°C for 1 minute. Immerse
the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder
solution at 270T5°C for 10T0.5 seconds. Let sit at room
temperature for 24T2 hours, then measure.
• Initial measurement for high dielectric constant type
Perform a heat treatment at 150+0/-10°C for one hour and
then let sit for 24T2 hours at room temperature.
Perform the initial measurement.
R230
Capacitance meter
45
Test Method
20
Fig. 3
50
Continued on the following page.
45
Pressurize
Pressurizing
speed : 1.0mm/sec.
Flexure : V1