DE2E3KY222MA2BM01 Murata, DE2E3KY222MA2BM01 Datasheet - Page 3

• Manufacturer Part Number: DE2E3KY222MA2BM01
• Description: Ceramic Disc Capacitors Class X1 Y2 2200pF 250Vac E 20%
• Manufacturer: Murata
• Series: DEr
• Type: Ceramic Discr

Specifications of DE2E3KY222MA2BM01

• Voltage Rating: 250 Volts
• Operating Temperature Range: - 25 C to + 125 C
• Termination Style: Radial
• Product: Ceramic Disc Capacitors - Other Various
• Dimensions: 8 mm Dia.
• Capacitance: 2200 pF
• Tolerance: 20 %
• Temperature Coefficient: E
• Lead Spacing: 5 mm
• Tolerance (+ Or -): 20%
• Voltage: 250VAC
• Temp Coeff (dielectric): E
• Operating Temp Range: -25C to 125C
• Mounting Style: Through Hole
• Package / Case: Not Required
• Construction: Radial
• Lead Spacing (nom): 5mm
• Product Length (mm): Not Requiredmm
• Product Depth (mm): 5mm
• Product Height (mm): Not Requiredmm
• Product Diameter (mm): 8mm
• Lead Diameter (nom): 0.6mm
• Seated Plane Height: 11mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

No.
14 Life
15 Flame Test
16
17 Active Flammability
*
Safety Standard Certified Type KY/KH/KX Specifications and Test Methods
2
"Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Continued from the preceding page.
Robustness
of
Terminations
Item
Appearance
Capacitance
Change
I.R.
Dielectric
Strength
Tensile
Bending
No marked defect
Within ±20%
3000MΩ min.
Per Item 6
The capacitor flame extinguishes as follows.
Lead wire should not be cut off. Capacitor should
not be broken.
The cheesecloth should not be on fire.
Cycle
1 to 4
5
Specifications
Time (sec.)
30 max.
60 max.
Impulse Voltage
Each individual capacitor should be subjected to a 5kV (Type
KX: 8kV) impulses for three times. Then the capacitors are
applied to life test.
Apply a voltage from Table 4 for 1000 hrs. at 125+2/-0°C, and
relative humidity of 50% max.
Post-treatment:
The capacitor should be subjected to applied flame for 15 sec.
and then removed for 15 sec. until 5 cycles are completed.
As shown in the figure at right, fix the body
of the capacitor and apply a tensile weight
gradually to each lead wire in the radial
direction of the capacitor up to 10N and keep
it for 10±1 sec.
Each lead wire should be subjected to 5N of weight and bent
90° at the point of egress, in one direction, then returned to its
original position and bent 90° in the opposite direction at the
rate of one bend in 2 to 3 sec.
The capacitor should be individually wrapped in at least one but
not more than two complete layers of cheesecloth. The
capacitor should be subjected to 20 discharges. The interval
between successive discharges should be 5 sec. The U
should be maintained for 2 min. after the last discharge.
C
L
C
C
F
1 to 4
1,2
t
x
Capacitor should be stored for 1 to 2 hrs. at room condition.*
0
100 (%)
90
50
30
AC425V(r.m.s.), except that once each hour the voltage
is increased to AC1000V(r.m.s.) for 0.1 sec.
S
: 1μF±10%
: 1.5mH±20% 16A Rod core choke
: 3μF±5% 10kV
: Capacitor under test
: Fuse, Rated 10A
1
Tr
T
T
1
T
2
S
2
U
U
AC
C
x
F
1
5kV
L
L
Applied Voltage
1
C
3
Gas Burner: Inside Dia. 9.5
Test Method
2
<Table 4>
t
L
L
C
2
4
Continued on the following page.
Front time (T
Time to half-value (T
Capacitor
3
C
R
U
U
U
3
AC
R
t
Flame
C
x
: 0.033μF±5% 10kV
: 100Ω±2%
: U
: Rated Voltage
: Voltage applied to C
time
R
Oscilloscope
1
±5%
R
C
) =1.2μs=1.67T
t
W
(in mm)
2
) =50μs
AC
U
t
2
t