BLM21BB221SH1D Murata, BLM21BB221SH1D Datasheet - Page 50

• Manufacturer Part Number: BLM21BB221SH1D
• Description: EMI/RFI Suppressors & Ferrites 0805 220ohms HiSpeed Signal Line Tape
• Manufacturer: Murata
• Series: BLM Br

Specifications of BLM21BB221SH1D

• Shielding: Unshielded
• Test Frequency: 100 MHz
• Product: Chip Ferrite Beads
• Impedance: 220 Ohms
• Tolerance: 25 %
• Maximum Dc Current: 200 mAmps
• Maximum Dc Resistance: 0.35 Ohms
• Operating Temperature Range: - 55 C to + 125 C
• Package / Case: 0805 (2012 metric)
• Termination Style: SMD/SMT
• Dc Resistance Max: 0.35ohm
• Dc Current Rating: 200mA
• Ferrite Mounting: SMD
• Ferrite Case Style: 0805 / 2012
• Operating Temperature Max: +125°C
• Operating Temperature Min: -55°C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
<Unless otherwise specified>
1. Electrical Performance
2. Mechanical Performance
48
No.
No.
Specifications and Test Methods
1
2
3
4
1
2
3
4
5
Test and Measurement Conditions
Temperature: Ordinary Temp. 15 to 35 C
Humidity: Ordinary Humidity 25 to 85% (RH)
Specifications
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Capacitance (Cap.)
Insulation Resistance
(I.R. )
Withstanding Voltage
Resistance to
Surge Voltage
Appearance and
Dimensions
Solderability
Resistance to
Soldering Heat
Bending Strength
Vibration
Item
Item
Within the specified tolerance.
1000M min.
Products should not be damaged.
Meet Table 2.
Table 2
Meet dimensions.
The electrodes should be at least 75% covered with
new solder coating.
Meet Table 2, above.
Meet Table 3.
Table 3
Meet Table 2, above.
Withstanding
Cap. Change
Cap. Change
Appearance
Appearance
Voltage
I.R.
33, 68, 100, 180,
33, 68, 100, 180,
1000, 3300 (pF)
1000, 3300 (pF)
360, 680 (pF)
360, 680 (pF)
Specifications
Specifications
1000M min.
No damage
No damage
No damage
within 15%
within 30%
within 15%
within 30%
<In case of doubt>
Temperature: 20 2 C
Humidity: 60 to 70% (RH)
Atmospheric Pressure: 86 to 106kPa
Table 1
Voltage: 100Vdc
Charging Time: 60 5s
Test Voltage: 250Vdc
Testing Time: 1 to 5s
Charge/Discharge Current: 10mA max.
Attenuating transient voltage of exponential function should be
applied to products in the following conditions.
Peak Voltage: 400V
Force Period: 1s
The number of Surges: 10
Visual Inspection and measured with micrometer.
Flux: Ethanol solution of rosin, 25wt%
Pre-heat: 150 10 C, 60 to 90s
Solder: qSn/Pb = 60/40
Solder Temperature: q230 5 C
Immersion Time: q4 1s
Immersion and emersion rates: 25mm/s
Flux: Ethanol solution of rosin, 25wt%
Pre-heat: 150 10 C, 60 to 90s
Solder: Sn/Pb = 60/40 or Sn-3.0Ag-0.5Cu solder
Solder Temperature: 270 5 C
Immersion Time: 10 1s
Immersion and emersion rates: 25mm/s
Then measured after exposure in room condition for 4 to
48 hrs.
It should be soldered on the Paper-phenol substrate. (t=1.6mm)
Deflection: 3.0mm
Keeping Time: 30s
It should be soldered on the substrate.
Oscillation Frequency: 10 to 2000 to 10Hz for 20 min.
Total Amplitude: 1.5mm or Acceleration amplitude 49m/s
whichever is smaller.
Testing Time: A period of 2 hours in each of 3 mutually
perpendicular directions (Total 6 hrs.)
180, 360, 680, 1000, 3300 (pF)
wSn-3.0Ag-0.5Cu solder
33, 68, 100 (pF)
Capacitance
w3 1s
E
B
w240 3 C
(for NFE61HT332Z2A9p: 250 5 C)
Test Methods
0.47 F
Test Methods
45
5
R340 F
Relay
Pressure jig
45
100
1 to 5Vrms
1 0.2Vrms
Voltage
10
Product
E
Deflection
B
Filter
1
2 3
400V
(in mm)
1MHz 10%
Frequency
1kHz 10%
2
C50E.pdf
1
08.8.28