BLM18BA750SN1D Murata, BLM18BA750SN1D Datasheet - Page 175

• Manufacturer Part Number: BLM18BA750SN1D
• Description: EMI/RFI Suppressors & Ferrites 0603 75 OHM
• Manufacturer: Murata
• Series: BLM Br

Specifications of BLM18BA750SN1D

• Shielding: Unshielded
• Test Frequency: 100 MHz
• Product: Chip Ferrite Beads
• Impedance: 75 Ohms
• Tolerance: 25 %
• Maximum Dc Current: 300 mAmps
• Maximum Dc Resistance: 0.7 Ohms
• Operating Temperature Range: - 55 C to + 125 C
• Package / Case: 0603 (1608 metric)
• Termination Style: SMD/SMT
• Dc Resistance Max: 0.7ohm
• Dc Current Rating: 300mA
• Ferrite Mounting: SMD
• Ferrite Case Style: 0603
• Inductor Case Style: 0603
• No. Of Pins: 2
• Core Material: Ferrite
• Resistance: 0.7ohm
• Rohs Compliant: Yes
• Operating Temperature Min: -55°C
• Operating Temperature Max: +125°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
Do not use products beyond the rated current and rated
voltage as this may create excessive heat and
deteriorate the insulation resistance.
1. Self-heating
2. Mounting Direction
<Operating Environment>
Do not use products in a chemical atmosphere such as
chlorine gas, acid or sulfide gas.
<Storage and Handling requirements>
1. Storage Period
1. Washing
2. Soldering
BLM (except BLM15E/15H/15G series) /BLA/NFM55/
DLM11G/DLM2HG series should be used within 6
months, the other series should be used within 12
months.
Solderability should be checked if this period is
exceeded.
Failure and degradation of a product are caused
by the washing method. When you wash in conditions
!Caution (Rating)
!Caution (Soldering and Mounting)
Notice (Storage and Operating Conditions)
Notice (Soldering and Mounting)
that are not in mounting information, please contact
Murata engineering.
Reliability decreases with improper soldering
methods. Please solder by the standard soldering
conditions shown in mounting information.
Please provide special attention when mounting chip
"EMIFIL" (BLM_P/K/S, NFM_P) series in close proximity
to other products that radiate heat.
The heat generated by other products may deteriorate
the insulation resistance and cause excessive heat in this
component.
Mount Chip Common Mode Choke Coils in right direction.
Wrong direction, which is 90 degrees rotated from right
direction, causes not only open or short circuit but also
flames or other serious trouble.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. Storage Conditions
3. Other
(1) Storage temperature: -10 to 40 degrees C
(2) Do not store products in a chemical atmosphere
Noise suppression levels resulting from Murata's
EMI suppression filters "EMIFIL" may vary,
depending on the circuits and ICs used, type of
noise, mounting pattern, lead wire length, mounting
location, and other operating conditions. Be sure
to check and confirm in advance the noise
suppression effect of each filter, in actual
circuits, etc. before applying the filter in a
commercial-purpose equipment design.
Relative humidity: 30 to 70%
Avoid sudden changes in temperature and
humidity.
such as chlorine gas, acid or sulfide gas.
right direction
Chip EMIFILr !Caution/Notice
Z
wrong direction
Z
173
C31E.pdf
08.9.1
6