PLA10AN4330R3R2B Murata, PLA10AN4330R3R2B Datasheet - Page 3
![Common Mode Inductors PLA10AN4330R3R2B](/photos/16/39/163935/pe0_810r_sml.jpg)
PLA10AN4330R3R2B
Manufacturer Part Number
PLA10AN4330R3R2B
Description
Common Mode Inductors PLA10AN4330R3R2B
Manufacturer
Murata
Datasheet
1.PLA10AN1030R7R2B.pdf
(3 pages)
Specifications of PLA10AN4330R3R2B
Dimensions
16 mm W x 18 mm L x 17.5 mm H
Product
Chokes
Shielding
Unshielded
Inductance
43 mH
Maximum Dc Current
0.3 Amp
Maximum Dc Resistance
100 mOhms
Operating Temperature Range
- 25 C to + 120 C
Termination Style
Through Hole
Dc Current Rating
300mA
Inductor Case Style
Through Hole
No. Of Pins
4
Body Diameter
1.2mm
Dc Current Max
0.3A
External Depth
16mm
External Length / Height
17.5mm
Rohs Compliant
Yes
Inductance Min
43mH
Insulation Resistance
100Mohm
Voltage Rating Vdc
300V
Termination Type
Through Hole
Filter Terminals
Through Hole
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PLA10AN4330R3R2B
Manufacturer:
MURATA
Quantity:
12 000
I !Caution (Rating)
I Notice (Other)
! Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
o
1. Rated Current
2. Inrush Current
If these conditions are exceeded, excessive heat may
cause fumes or permanent damage to the component,
or at worst cause ignition.
Coil Humming Noise
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
specifications or transact the approval sheet for product specifications before ordering.
Magnetic flux generated between coil and core or
between the choke coil windings creates repulsive
power between the coil windings. This repulsive
power causes the coil winding to vibrate and create
a humming noise. The amount of hum produced by the
coil is proportionate to the amount of harmonic
distortion generated by the operating current. This
does not influence the electrical performance of
the coils, but it should be considered and tested
in actual circuit application.
Continued from the preceding page.
This data sheet is applied for AC Line Filters Common Mode Choke Coil used for General Electronics equipment for your design.
Operating current should not exceed the rated
value. Even if operating current is under the
rated value, adequate ventilation is required to
avoid excessive heat generated within the product
(choke coil) and from surrounding heat sources.
If exceeding these conditions, excessive heat may
cause fumes or permanent damage to the product.
Please ensure that product (choke coil) is
evaluated and confirmed against the specification
when it is mounted in your final assembled product.
-> Winding temperature should be less than
*As for FKOB series winding temperature should be
less than 95 degree C.
Maximum allowable temperature at the surface of
coil (ambient temperature + winding temperature
rise) is in accordance with each safety standard
applicable to final assembled product.
When the temperature at winding exceeds maximum
allowable temperature of safety standard, the
rated current should be derated.
Inrush current should not exceed 10 times rated
current within 1/4 cycle of 50/60Hz commercial
power line. Inrush current should be limited to a
minimum of 10 seconds after last inrush.
120 degree C.
Noise Suppression Products/EMI Suppression Filters > AC Line Filters > Common Mode Choke Coil
http://www.murata.com/
Data Sheet
I Notice (Soldering and Mounting)
Magnetic Flux Leakage
Choke coils generate small amounts of magnetic flux
leakage that may adversely affect equipment operation
according to component arrangement.
Testing should be completed on final assembly to
ensure equipment performance is not affected.
2007.7.4
3