ERJ-6ENF75R0V Panasonic, ERJ-6ENF75R0V Datasheet - Page 5

no-image

ERJ-6ENF75R0V

Manufacturer Part Number
ERJ-6ENF75R0V
Description
Thick Film Resistors - SMD Thick Film Chip Res 08051% Precision
Manufacturer
Panasonic
Series
ERJ-6Er
Datasheet

Specifications of ERJ-6ENF75R0V

Resistance
75 Ohms
Tolerance
1 %
Power Rating
0.125 Watt (1/8 Watt)
Termination Style
SMD/SMT
Package / Case
0805 (2013 metric)
Operating Temperature Range
- 55 C to + 155 C
Dimensions
1.25 mm W x 2 mm L x 0.6 mm H
Product
Thick Film Resistors SMD
Temperature Coefficient
+/- 100 PPM / C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
In case of fl ow soldering, the land width must be smaller than the Chip Resistor width to control the sol der amount properly.
Generally, the land width should be 0.7 to 0.8 times (W) of the width of chip resistor. In case of refl ow soldering, solder
amount can be adjusted, therefore the land width should be set to 1.0 to 1.3 times chip resistor width (W).
The following are precautions for individual products. Please also refer to the precautions common to Fixed Resistors
shown on page ER2 of this catalog.
1. Take measures against mechanical stress during and after mounting of Precision Thick Film Chip Resistors (here af ter
2. If a transient load (heavy load in a short time) like a pulse is expected to be applied, check and evaluate the operations
3. Do not use halogen-based or other high-activity fl ux. Otherwise, the residue may impair the resistors' per for mance
4. When soldering with a soldering iron, never touch the resistors' bodies with the tip of the soldering iron. When using a
5. As the amount of applied solder becomes larger, the mechanical stress applied to the resistors increases, causing
6. Do not apply shock to the resistors or pinch them with a hard tool (e.g. pliers and tweezers). Oth er wise, the re sis tors'
7. Avoid excessive bending of printed circuit boards in order to protect the resistors from abnormal stress.
Design and specifi cations are each subject to change without notice. Ask factory for the current technical specifi cations before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Recommended Land Pattern
Recommended Soldering Conditions
called the resistors) so as not to damage their electrodes and protective coatings.
of the resistors when installed in your products before use.
Never exceed the rated power. Otherwise, the performance and/or reliability of the resistors may be impaired.
and/or reliability.
soldering iron with a high temperature tip, fi nish soldering as quickly as possible (within three seconds at 350 °C max.).
problems such as cracks and faulty characteristics. Avoid applying an excessive amount of solder.
protective coatings and bodies may be chipped, affecting their performance.
Recommendations and precautions are described below.
● Recommended soldering conditions for refl ow
● Recommended soldering conditions for fl ow
· Refl ow soldering shall be performed a maximum of
· Please contact us for additional information when
· Please measure the temperature of the terminals
Safety Precautions
two times.
used in conditions other than those specifi ed.
and study every kind of solder and printed circuit
board for solderability be fore ac tu al use.
Preheating
Soldering
Preheating
Peak
a
b
Time
140 °C to 180 °C
Temperature
245 ± 5 °C
Chip Resistor
Heating
For soldering
60 s to 120 s
20 s to 30 s
Time
For soldering (Example : Sn/Pb)
For lead-free soldering (Example : Sn/Ag/Cu)
ERJXG
ERJ1G, 1R
ERJ2R
ERJ3R, 3EK (0603)
ERJ6R, 6EN (0805)
ERJ8EN
ERJ14N
ERJ12N
ERJ12S
ERJ1TN
Preheating
Main heating
Peak
Preheating
Main heating
Peak
Type (inches)
Precision Thick Film Chip Resistors
150 °C to 180 °C
(01005) 0.15 to 0.2
(0201)
(0402)
(1206)
(1210)
(1812)
(2010)
(2512)
Temperature
max. 260 °C
140 °C to 160 °C
150 °C to 180 °C
For lead-free soldering
Above 200 °C
Above 230 °C
Temperature
Temperature
max. 260 °C
235 ± 5 °C
0.3 to 0.4
0.5 to 0.6
0.7 to 0.9
3.3 to 3.7
1 to 1.4
2 to 2.4
2 to 2.4
3.6 to 4
5 to 5.4
a
Dimensions (mm)
0.5 to 0.7
0.8 to 0.9
3.2 to 3.8
5.7 to 6.5
1.4 to 1.6
7.6 to 8.6
2 to 2.2
4.4 to 5
4.4 to 5
6.2 to 7
60 s to 120 s
b
max. 10 s
60 s to 120 s
60 s to 120 s
30 s to 40 s
30 s to 40 s
max. 10 s
Time
max. 10 s
Time
Time
0.20 to 0.25
0.25 to 0.35
0.4 to 0.6
2.3 to 3.5
2.3 to 3.5
0.9 to 1.4
1.2 to 1.8
1.8 to 2.8
1.8 to 2.8
0.8 to 1
Feb. 2006
c

Related parts for ERJ-6ENF75R0V