USB-RS232-WE-1800-BT_5.0 FTDI, USB-RS232-WE-1800-BT_5.0 Datasheet - Page 13
![Cables (Cable Assemblies) USB to RS232 Embeded Conv 5V WireEnd 1.8m](/photos/17/30/173018/usb-rs232-we-1800-bt_sml.jpg)
USB-RS232-WE-1800-BT_5.0
Manufacturer Part Number
USB-RS232-WE-1800-BT_5.0
Description
Cables (Cable Assemblies) USB to RS232 Embeded Conv 5V WireEnd 1.8m
Manufacturer
FTDI
Datasheet
1.USB-RS232-WE-1800-BT.pdf
(15 pages)
Specifications of USB-RS232-WE-1800-BT_5.0
Product
USB to Serial Assemblies
Number Of Conductors
6
Wire Size (awg)
24
Connector End A
USB Type A Plug
Connector End B
Wire End
Length
1.8 m
Cable Type
USB to RS-232 Serial Converter Cable
Description/function
USB to Serial Cable Assembly
Equipment Type
USB to Serial Cable Adapter
Voltage Rating
5 V
Color
Black
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Appendix A - Cable EEPROM Configuration
Each USB-RS232 cable is controlled by the FTDI FT232R IC. This FT232R device contains an EEPROM
which contains the USB configuration descriptors for that device. When the cable is plugged into a PC or a
USB reset is performed, the PC will read these descriptors. The default values stored into the internal
EEPROM are defined in Table 0.1
Parameter
USB Vendor ID (VID)
USB Product UD (PID)
Serial Number Enabled?
Serial Number
Pull down I/O Pins in USB
Suspend
Manufacturer Name
Product Description
Max Bus Power Current
Power Source
Device Type
USB Version
Remote Wake Up
High Current I/Os
Load VCP Driver
Invert TXD
Invert RXD
Invert RTS#
Invert CTS#
Table 0.1 Default Internal EEPROM Configuration
The internal EEPROM in the cable can be re-programmed over USB using the utility program MPROG.
MPROG can be downloaded from the www.ftdichip.com. Version 2.8a or later is required for the FT232R
chip. Users who do not have their own USB Vendor ID but who would like to use a unique Product ID in
their design can apply to FTDI for a free block of unique PIDs. Contact FTDI support for this service.
Copyright © 2010 Future Technology Devices International Limited
Bus Powered
USB TO RS232 SERIAL CONVERTER RANGE OF CABLES Datasheet Version 1.3
See Note
See note
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
FT232R
0403h
6001h
90mA
Value
0200
FTDI
Yes
FTDI default VID (hex)
FTDI default PID (hex)
A unique serial number is generated and programmed into
the EEPROM during device final test.
Enabling this option will make the device pull down on the
UART interface lines when the power is shut off (PWREN#
is high).
USB-RS232-WE
Returns USB 2.0 device description to the host.
Note: The device is a USB 2.0 Full Speed device (12Mb/s)
as opposed to a USB 2.0 High Speed device (480Mb/s).
Enables the high drive level on the UART and CBUS I/O
pins.
Makes the device load the VCP driver interface for the
device.
Signal on this pin becomes TXD# if enable.
Signal on this pin becomes RXD# if enable.
Signal on this pin becomes RTS if enable.
Signal on this pin becomes CTS if enable.
Document Reference No.: FT_000077
Notes
Clearance No.: FTDI# 51
12