E2EQ-X7D1-M1GJ Omron, E2EQ-X7D1-M1GJ Datasheet - Page 7

• Manufacturer Part Number: E2EQ-X7D1-M1GJ
• Description: Proximity Sensors With M12 Pigtail 1&4
• Manufacturer: Omron
• Type: Inductive Proximity Sensorr
• Series: E2EQr

Specifications of E2EQ-X7D1-M1GJ

• Maximum Operating Temperature: + 70 C
• Supply Voltage: 24 V
• Operating Supply Voltage: 10 V to 30 V
• Minimum Operating Temperature: - 25 C
• Maximum Output Current: 100 mA
• Barrel Size: M18
• Features: NO
• Sensing Distance: 7 mm
• Sensor Type: Inductive
• Sensing Object: Metallic
• Response Frequency: 500Hz
• Material - Body: Fluoroplastic Coated Brass
• Shielding: Shielded
• Voltage - Supply: 10 V ~ 30 V
• Output Type: NPN-NO
• Terminal Type: Connector
• Package / Case: Cylinder, Threaded - M18
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Precautions
J INSTALLATION AND SURROUNDINGS
Do not tighten the nut with excessive force. A washer must be
used with the nut.
Note: The table below shows the tightening torques for part A
J EFFECTS OF SURROUNDING METAL
When mounting the E2EQ within a metal panel, ensure that the
clearances given in the following table are maintained. Failure to
maintain these distances may cause deterioration in the
performance of the Sensor.
E2EQ
Model
E2EQ-X3D1-j
E2EQ-X7D1-j
E2EQ-X10D1-j
Model
ℓ
d
D
m
n
and part B nuts. In the above example, the nut is on the
sensor head side (part B) and hence the tightening torque
for part B applies. If this nut is in part A, the tightening
torque for part A applies instead.
ℓ
E2EQ-X3D1-j
0 mm
12 mm (0.47 in)
0 mm
8 mm (0.31 in)
18 mm (0.71 in)
Part A
Length
24 mm
29 mm
26 mm
D
E2EQ-X7D1-j
0 mm
18 mm (0.71 in)
0 mm
20 mm (0.79 in)
27 mm (1.06 in)
Shielded Model
Torque
150 kgf S cm
(11 1 ft S lbf)
(11.1 ft S lbf)
(15 N S m)
400 kgf S cm
(39 N S m)
(28.7 ft S lbf)
d dia.
Part B Part A
E2EQ-X10D1-j
0 mm
30 mm (1.18 in)
0 mm
40 mm (1.57 in)
45 mm (1.77 in)
Part B
Torque
---
800 kgf S cm
(78 N S m)
n
m
J MUTUAL INTERFERENCE
When installing two or more E2EQ face-to-face or side-by-side,
ensure that the minimum distances given in the following table
are maintained.
J SENSING OBJECT
Sensing Object Material
The sensing distance is reduced for non-magnetic metals. The
sensing distance for non-magnetic metal foils less than 0.01 mm
thick is the same as that for magnetic metals. However, if the foil
becomes so thin (e.g., from vaporization) that it loses its
conductivity, then it will become undetectable.
Metal Plating
The sensing distance will change if the sensing object is plated.
The following table shows the sensing distance of a plated object
as a percentage of the sensing distance of an un-plated object.
Model
E2EQ-X3D1-j
E2EQ-X7D1-j
E2EQ-X10D1-j
Plating thickness
No plating
Zn 5 to 15 µm
Cd 5 to 15 µm
Ag 5 to 15 µm
Cu 10 to 20 µm
Cu 5 to 15 µm
Cu (5 to 10 µm) + Ni
(10 to 20 µm)
Cu (5 to 10 µm) +
Ni (10 µm) + Cr (0.3 µm)
A
A
30 mm (1.18 in)
50 mm (1.97 in)
100 mm (3.93) in)
B
Iron
100%
90% to 120%
100% to 110%
60% to 90%
70% to 95%
---
75% to 95%
75% to 95%
B
20 mm (0.79 in)
35 mm (1.38 in)
70 mm (2.76 in)
Brass
100%
95% to 105%
95% to 105%
85% to 100%
95% to 105%
95% to 105%
---
---
E2EQ
7