MSO3014 Tektronix, MSO3014 Datasheet - Page 7

• Manufacturer Part Number: MSO3014
• Description: Benchtop Oscilloscopes 100MHZ, 2.5GS/S 4+16 CHANNELS
• Manufacturer: Tektronix
• Type: Mixed Signalr

Specifications of MSO3014

• Equipment Type: Oscilloscope
• Sampling Rate: 2.5 GS/s
• Bandwidth: 100 MHz
• Display Type: WVGA Color 9 in
• Brand/series: MSO3000 Series
• Configuration: Bench/Portable
• Memory: 5 Mpts
• Number Of Channels: 4 Analog + 16 Digital
• Sample Rate: 2.5 GS/s analog, 500 MS/s dogtial main, 8.25 GS/s digital MagniVu
• Record Length: 5 M Points
• Input Impedence: 50Ω, 75Ω, 1MΩ
• Waveform Capture Rate: 50,000 wfm/s
• Power Analysis: Optional
• Standard I/o: (2) USB Host, USB Device, LAN, Video
• Display: 9.0 inch WVGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Triggering on a specific data packet going across an I
clock and the blue waveform is data. A bus waveform provides decoded packet content
including Start, Address, Read/Write, Data, and Stop.
Serial Triggering and Analysis (Optional)
On a serial bus, a single signal often includes address, control, data, and
clock information. This can make isolating events of interest difficult. The
MSO/DPO3000 Series offers a robust set of tools for debugging serial
buses with automatic trigger, decode, and search for I
RS-232/422/485/UART, and I
Serial Triggering
Trigger on packet content such as start of packet, specific addresses,
specific data content, unique identifiers, etc. on popular serial interfaces
such as I
Bus Display
Provides a higher-level, combined view of the individual signals (clock, data,
chip enable, etc.) that make up your bus, making it easy to identify where
packets begin and end and identifying subpacket components such as
address, data, identifier, CRC, etc.
Bus Decoding
Tired of having to visually inspect the waveform to count clocks, determine
if each bit is a 1 or a 0, combine bits into bytes, and determine the hex
value? Let the oscilloscope do it for you! Once you’ve set up a bus, the
2
C, SPI, CAN, LIN, RS-232/422/485/UART, and I
2
S/LJ/RJ/TDM.
2
C bus. The yellow waveform is
2
C, SPI, CAN, LIN,
2
S/LJ/RJ/TDM.
Digital Phosphor Oscilloscopes — MSO3000 Series, DPO3000 Series
Event table showing decoded Identifier, DLC, DATA, and CRC for every CAN packet in
a long acquisition.
MSO/DPO3000 Series will decode each packet on the bus, and display the
value in hex, binary, decimal (LIN only), signed decimal (I
only), or ASCII (RS-232/422/485/UART only) in the bus waveform.
Event Table
In addition to seeing decoded packet data on the bus waveform itself, you
can view all captured packets in a tabular view much like you would see in
a software listing. Packets are time stamped and listed consecutively with
columns for each component (Address, Data, etc.).
Search
Serial triggering is very useful for isolating the event of interest, but once
you’ve captured it and need to analyze the surrounding data, what do
you do? In the past, users had to manually scroll through the waveform
counting and converting bits and looking for what caused the event. With
the MSO/DPO3000 Series, you can have the oscilloscope automatically
search through the acquired data for user-defined criteria including serial
packet content. Each occurrence is highlighted by a search mark. Rapid
navigation between marks is as simple as pressing the Previous (←) and
Next (→) buttons on the front panel.
www.tektronix.com
2
S/LJ/RJ/TDM
7