13287 AIM - American Iron and Metal, 13287 Datasheet
13287
Manufacturer Part Number
13287
Description
Solder, Fluxes & Accessories SN60/Pb40 RA 3% .025 DIA 1 lb.
Manufacturer
AIM - American Iron and Metal
Datasheet
1.14315.pdf
(1 pages)
Specifications of 13287
Description/function
Rosin Activated
Alloy
Sn60Pb40
Diameter
0.025 in
Weight
1 lb
Core Size
3%
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features:
- High Activity Level
- Good Thermal Transfer
Description:
RA is a fully activated, general-purpose wire solder for use in applications where mildly activated fluxes are too weak. RA
cored wire is strong enough for excellent tarnish and oxide removal, and will produce bright shiny solder joints. RA wire
will leave slight to moderate post process residues that may be left on noncritical applications, but should be removed from
any critical applications. RA cored wire meets Mil-Spec cleanliness requirements post-cleaning. IPC flux classification for
this material is ROM1.
Availability:
-
-
-
-
-
Application:
-
-
-
-
-
Cleaning:
If post-process cleaning is desired, is easiest if performed within a two to three hour period. Adequate cleaning may be
accomplished using a saponifier. AIMTERGE-520A is recommended. A temperature of 35°C-65°C (100ºF-150ºF) is
sufficient for removing residues. An in-line or other pressurized spray cleaning system is suggested, but is not required.
Handling and Storage:
-
-
-
Safety:
-
-
-
The information contained herein is based on data considered accurate and is offered at no charge. Product information is based upon the assumption of
proper handling and operating conditions. All information pertaining to solder paste is produced with 45-micron powder. Liability is expressly
disclaimed for any loss or injury arising out of the use of this information or the use of any materials designated. Please refer to
http://www.aimsolder.com/terms.cfm
RA is standard with a 3.0% flux core for tin-lead (2.0% flux core for lead-free) alloys.
RA is available in Sn/Pb, Sn/Ag/Cu, SN100C
Standard spool sizes: ½ lb. for .010 and .015 diameters; 1 lb. for .020, .032, .040, .050, and .062 diameters.
Packaging of ½ lb. and 1 lb. spools is standard in 12 lb. and 24 lb. cases.
Other flux percentages, alloys, diameters and spool sizes may be available upon special request.
Solder iron tip temperature should be between 340°C-400°C (650°F-750°F) for Sn63, Sn62 and Sn60 alloys, 370°C-
425°C (700°F-800°F) for Sn/Ag and Sn/Ag/Cu alloys and 340°C-370°C (650°F-700°F) for Sn43/Pb43/Bi14.
Hold the solder iron at a 45° to 60° angle to the work surface.
The solder iron should contact both the component lead and PCB pad surface.
Solder and flux should flow onto both the lead and pad or lead and barrel to promote optimum flux activity to the joint
being worked.
If additional flux is needed, the use of AIM’s RA301 flux is recommended. Operators should use an applicator capable
of dispensing precise amounts of flux to eliminate over-saturation and excessive spread.
RA cored wire has an indefinite shelf life when proper storage conditions are observed.
Store RA in a clean dry area away from moisture and sunlight.
Do not freeze this product.
Use with adequate ventilation and proper personal protective equipment.
Refer to the accompanying MSDS for any specific emergency information.
Do not dispose of any waste materials in non-approved containers.
USA +1-401-463-5605 · Canada +1-514-494-2000 · Europe +44-1737-222-258 · Mexico +52-656-630-0032 · Asia-Pacific +86-755-2993-6487
to review AIM's terms and conditions.
RA Cored Wire Solder
Manufacturing and Distribution Worldwide
Rosin Activated Cored Wire Solder
- Fully Activated Flux
- Glycol-Free
info@aimsolder.com · www.aimsolder.com
®
AIM
alloys.
IS
ISO9001:2008 C
ERTIFIED
- Improved Wetting Properties
08/09
Rev 2