MC1455BDR2G ON Semiconductor, MC1455BDR2G Datasheet - Page 5

• Manufacturer Part Number: MC1455BDR2G
• Description: IC OSC MONO TIMING 8-SOIC
• Manufacturer: ON Semiconductor
• Type: 555 Type, Timer/Oscillator (Single)r

Specifications of MC1455BDR2G

• Current - Supply: 10mA
• Mounting Type: Surface Mount
• Voltage - Supply: 4.5 V ~ 16 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Rohs Compliant: YES
• # Internal Timers: 1
• Power Dissipation: 625mW
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (typ): 5/9/12/15V
• Operating Supply Voltage (max): 16V
• Package Type: SOIC N
• High Level Output Current: -200mA
• Low Level Output Current: 200mA
• Pin Count: 8
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Count: -
• Frequency: -
• Lead Free Status / Rohs Status: Compliant
• Other names: MC1455BDR2G; MC1455BDR2GOSTR

external resistor − capacitor network as its timing element. It
can be used in both the monostable (one−shot) and astable
modes with frequency and duty cycle controlled by the
capacitor and resistor values. While the timing is dependent
upon the external passive components, the monolithic circuit
provides the starting circuit, voltage comparison and other
functions needed for a complete timing circuit. Internal to the
integrated circuit are two comparators, one for the input
signal and the other for capacitor voltage; also a flip−flop and
digital output are included. The comparator reference
voltages are always a fixed ratio of the supply voltage thus
providing output timing independent of supply voltage.
Monostable Mode
are used for the timing network. Both the threshold terminal
and the discharge transistor terminal are connected together
in this mode (refer to circuit in Figure 14). When the input
voltage to the trigger comparator falls below 1/3 V
comparator output triggers the flip−flop so that its output sets
low. This turns the capacitor discharge transistor “off” and
drives the digital output to the high state. This condition
allows the capacitor to charge at an exponential rate which is
set by the RC time constant. When the capacitor voltage
reaches 2/3 V
flip−flop. This action discharges the timing capacitor and
returns the digital output to the low state. Once the flip−flop
The MC1455 is a monolithic timing circuit which uses an
In the monostable mode, a capacitor and a single resistor
Threshold
Discharge
Trigger
Reset
CC
GND
V
CC
, the threshold comparator resets the
Reset
4.7 k
Discharge
10 k
Comparator
Threshold
Figure 13. Representative Circuit Schematic
830
100
100 k
4.7 k
GENERAL OPERATION
CC
http://onsemi.com
, the
Comparator
1.0 k
Trigger
5
5.0 k
5.0 k
5.0 k
has been triggered by an input signal, it cannot be retriggered
until the present timing period has been completed. The time
that the output is high is given by the equation t = 1.1 R
Various combinations of R and C and their associated times
are shown in Figure 16. The trigger pulse width must be less
than the timing period.
interrupting the timing cycle. As long as the reset pin is low,
the capacitor discharge transistor is turned “on” and prevents
the capacitor from charging. While the reset voltage is applied
the digital output will remain the same. The reset pin should
be tied to the supply voltage when not in use.
A reset pin is provided to discharge the capacitor, thus
Control Voltage
R
R
L
L
c b
Trigger
Output
e
3
2
Figure 14. Monostable Circuit
Flip-Flop
7.0 k
4.7 k
+V
Reset
CC
(5.0 V to 15 V)
4
6.8 k
MC1455
1
c
4.7 k
V
8
220
Output
CC
3.9 k
Threshold
Control
Voltage
b
Discharge
7
6
5
Output
0.01 mF
R
C
A
A
C.