PC28F256P30B85A NUMONYX, PC28F256P30B85A Datasheet - Page 38
![no-image](/images/manufacturer_photos/0/4/484/numonyx_sml.jpg)
PC28F256P30B85A
Manufacturer Part Number
PC28F256P30B85A
Description
IC FLASH 256MBIT 85NS 64EZBGA
Manufacturer
NUMONYX
Series
StrataFlash™r
Datasheet
1.RD48F4400P0VBQEJ.pdf
(97 pages)
Specifications of PC28F256P30B85A
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
256M (16Mx16)
Speed
85ns
Interface
Parallel
Voltage - Supply
1.7 V ~ 2 V
Operating Temperature
-40°C ~ 85°C
Package / Case
64-TBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
873888
873888
PC28F256P30B85
PC28F256P30B85 873888
873888
PC28F256P30B85
PC28F256P30B85 873888
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PC28F256P30B85A
Manufacturer:
Micron Technology Inc
Quantity:
10 000
10.1.4
Figure 12: Block Locking State Diagram
10.1.5
Note:
Datasheet
38
or Lock-Down Block produces a command sequence error and set Status Register bits SR[4]
and SR[5]. If a command sequence error occurs during an erase suspend, SR[4] and SR[5]
remains set, even after the erase operation is resumed. Unless the Status Register is cleared
using the Clear Status Register command before resuming the erase operation, possible erase
errors may be masked by the command sequence error.
A Lock Block Setup command followed by any command other than Lock Block, Unlock Block,
Power-Up/Reset
Notes:
Block Lock Status
The Read Device Identifier command is used to determine a block’s lock status (see
Section 12.0, “Power and Reset Specifications” on page
the addressed block’s lock status; DQ0 is the addressed block’s lock bit, while DQ1 is
the addressed block’s lock-down bit.
Block Locking During Suspend
Block lock and unlock changes can be performed during an erase suspend. To change
block locking during an erase operation, first issue the Erase Suspend command.
Monitor the Status Register until SR[7] and SR[6] are set, indicating the device is
suspended and ready to accept another command.
Next, write the desired lock command sequence to a block, which changes the lock
state of that block. After completing block lock or unlock operations, resume the erase
operation using the Erase Resume command.
1. [a,b,c] represents [WP#, DQ1, DQ0]. X = Don’t Care.
2. DQ1 indicates Block Lock-Down status. DQ1 = ‘0’, Lock-Down has not been issued
3. DQ0 indicates block lock status. DQ0 = ‘0’, block is unlocked. DQ0 = ‘1’, block is
4. Locked-down = Hardware + Software locked.
5. [011] states should be tracked by system software to determine difference between
to this block. DQ1 = ‘1’, Lock-Down has been issued to this block.
locked.
Hardware Locked and Locked-Down states.
Unlocked
Locked
[X01]
[X00]
Software Block Lock (0x60/0x01) or Software Block Unlock (0x60/0xD0)
Software Block Lock-Down (0x60/0x2F)
W P# hardware control
Software
Locked-
Down
Locked
[111]
[011]
4,5
WP# Hardware Control
50). Data bits DQ[1:0] display
Hardware
Unlocked
Locked
[011]
[110]
5
August 2008
306666-12
P30