55892-1 Tyco Electronics, 55892-1 Datasheet

Solderless Terminal Kit

55892-1

Manufacturer Part Number
55892-1
Description
Solderless Terminal Kit
Manufacturer
Tyco Electronics
Datasheet
1.55892-1.pdf (2 pages)

Specifications of 55892-1

Kit Contents
10 [12-10 AWG] Splice, 15 [22-18 AWG] Splice, 25 [16-14 AWG] Splice, Molded Case And Crimping Tool
Leaded Process Compatible
Yes
Kit Type
Sealed Connector System
Values
51 pcs - 10 ea 12 ~ 10AWG , 15 ea 22 ~ 18AWG, 25 ea 16 ~ 14 AWG Splice, Crimp Tool
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
A09093
1. INTRODUCTION
Hand Tool 55893–1 is used to crimp Pre–Insulated
Heat Shrink Terminals and Splices onto 22 –10 AWG
wire. See Figure 2. This hand tool is equipped with a
ratchet mechanism to ensure reliable crimp
terminations.
Hand Tool 55893–1 is available in a “Seal and Splice
Kit” with assorted terminals and splices by ordering
part number 55892–1. Information about Hand Tool
55894–1 which crimps the same terminals and splices
with a wire size range of 16–8 AWG may be found on
Instruction Sheet 408–8891.
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended–use, production operations is available.
E
All International Rights Reserved
AMP and Tyco are trademarks. *Trademark
Other products, logos, and company names used are the property of their respective owners.
2004 Tyco Electronics Corporation, Harrisburg, PA
Die Nests
Crimping
Head
Ratchet
Tool Handles
(See Figure 1)
Figure 1
This controlled document is subject to change.
For latest revision, call the FAX/PRODUCT INFO number.
Hand Tool 55893–1
for Pre–Insulated Heat Shrink
Terminals and Splices
2. CRIMPING PROCEDURE
Select an appropriate terminal or splice for the tool.
Cut and strip the wire to the proper length. For 22–14
AWG wire, strip the length to 7.94 [.313]; for 12–10
AWG wire, strip the length to 9.52 [.375].
To open the tool, close the handles past the ratchet
release position which will allow the jaws to fully open.
Proceed with the following steps as shown in
Figure 3.
Ring Tongue
Terminal
Spade Terminal
Butt Splice
250 Series
FASTON*
Terminals
TERMINAL/SPLICE
250 Series FASTON
NOTE
Receptacle
Spade Terminal
Ring Tongue
Butt Splice
Terminals
Terminal
Dimensions in this instruction sheet are in
millimeters [with inches in brackets]. Figures are
for reference only and are not drawn to scale.
Tab
TOOLING ASSISTANCE CENTER 1–800–722–1111
FAX/PRODUCT INFO 1–800–522–6752
For Regional Customer Service, visit our website at
www.tycoelectronics.com
WIRE SIZE,
Figure 2
22–18
16–14
12–10
22–14
12–10
22–10
16–14
AWG
8, 10, 1/4, 5/16, 3/8, 1/2
6, 8, 10, 1/4, 5/16, 3/8
Instruction Sheet
408–8890
02 FEB 04 Rev O
STUD SIZE
6, 8, 10, 1/4
6, 8, 10
8, 10
–––
–––
1 of 2
LOC B

55892-1 Summary of contents

Page 1

... Hand Tool 55893–1 is available in a “Seal and Splice Kit” with assorted terminals and splices by ordering part number 55892–1. Information about Hand Tool 55894–1 which crimps the same terminals and splices with a wire size range of 16–8 AWG may be found on Instruction Sheet 408– ...

Page 2

Crimping Head Terminal 1. To crimp the wire barrel, center the wire barrel of the terminal or splice in the appropriate wire barrel crimp section according to the correct wire size range. Refer to Figure 2. The wire barrel insulation ...