71743-1040 Molex Inc, 71743-1040 Datasheet - Page 7

• Manufacturer Part Number: 71743-1040
• Description: CONN RCPT 40POS .050 VERT SCA-2
• Manufacturer: Molex Inc
• Series: EBBIr

Specifications of 71743-1040

• Pitch Spacing: 1.27mm
• No. Of Rows: 2
• No. Of Contacts: 40
• Gender: Receptacle
• Contact Termination: Through Hole
• Contact Plating: Gold
• Connector Type: Board To Board
• Product Type: Receptacles
• Pitch: 2.54 mm
• Mounting Style: Through Hole
• Mounting Angle: Vertical
• Number Of Positions / Contacts: 6
• Number Of Rows: 2
• Housing Material: High Temperature Thermoplastic
• Contact Material: Phosphor Bronze
• Voltage Rating: 30 V
• Current Rating: 1 A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 071743-1040::071743-1040-E::0717431040::0717431040-E::71743-1040-E::717431040::717431040-E::SDA-71743-104

REVISION:
DOCUMENT NUMBER:
7.0 RELIABILITY TEST REQUIREMENTS
H
TEST
General Examination
Mating Force
Durability and LLCR
Shock
Vibration
Unmating Force
Mixed Flowing Gas
Temperature Life
Thermal Shock
Humidity – Temperature
Cycling
Current vs. temperature
rise
Insulation resistance
Resistance to solvents
Compliant to PCB hole
cycling
Compliant to PCB
insertion force
Compliant to PCB
retention force
PS-73826-0000
ECR/ECN INFORMATION:
EC No:
DATE:
UCP2008-0355
2007/08/18
PRODUCT SPECIFICATION
EIA#
364-18
361-13
364-23
364-27
364-28
354-13
364-65
364-17
364-32
364-31
364-70
364-21
364-11
N/A
N/A
N/A
TITLE:
CREATED / REVISED BY:
BANAKIS/BBARKER
CRITERIA
Visual and dimensional
inspection
Force to mate 1.08N,
(110gf) maximum per
contact
Low level contact
Resistance < 15 milliohm
initial
Continuity < 1 micro-
second
Continuity < 1 micro-
Second. LLCR change < 15
milliohms
Force to unmate 0.15N
(15gf) minimum per contact
No physical damage and
shall meet all requirements
of subsequent tests
No physical damage and
shall meet all requirements
of subsequent tests
No physical damage and
shall meet requirements of
subsequent tests
No physical damage and
shall meet requirements of
subsequent tests
30 degree max.
temperature rise
1000 megaohms min.
No defect or damage that
would impair normal
operations
No fracture or break-out of
PTH
Maximum insertion force
allowed is 15 lbs per circuit
Minimum retention force of
compliant to PCB allowed is
1.5 lbs. min per circuit
PRODUCT SPECIFICATION
CONNECTOR GROUP
MOLEX SCA-2
CHECKED BY:
DMORGAN
COMMENTS
No defects allowed that may impair
normal operation
Measure the force to mate at a rate
of 12.7 mm per minute max.
20 mV max. open circuit at 100mA
max.; measured at 0, 50, 250, and
500 cycles
30 G peak acceleration, half sine. 3
shocks along 3 perpendicular
planes.
15-500-15 Hz random, for 1 hr. in
each of 3 mutually perpendicular
planes.
Measure the force to unmate at a
rate of 12.7 mm per minute max.
Class II for 14 days mated. Includes
compliant interface where
applicable.
105 degrees C for 1000 hours
5 cycles between -55 C and
105 C, mated connectors
10 cycles between 25 C and
65 C, at 95% rh , 240 hrs. mated
connectors.
2A. max. for two voltage applied
contact positions, 3A max. for 3
voltage applied contact positions
Test voltage 500 volt dc
Exposure to trichloroethylene
Each set of PTH’s are cycled 3
times using a new connector each
cycle
Press connector to PCB, the force
to seat should not exceed 15 lbs. /
circuit
Removal of connector or contacts
from PCB should yield a force > 1.5
lb./ contact
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
APPROVED BY:
SMILLER
SHEET No.
7
of
7