09 15 000 6107 HARTING, 09 15 000 6107 Datasheet - Page 21
![CONTACT, MALE, 26-22AWG, CRIMP](/photos/18/93/189347/4306413_sml.jpg)
09 15 000 6107
Manufacturer Part Number
09 15 000 6107
Description
CONTACT, MALE, 26-22AWG, CRIMP
Manufacturer
HARTING
Series
Han Dr
Datasheet
1.09_99_000_0099.pdf
(25 pages)
Specifications of 09 15 000 6107
Connector Type
Contact, Crimp
Current Rating
10A
Contact Plating
Silver
Wire Size (awg)
26-22
Contact Termination
Crimp
Contact Gender
Pin
Rohs Compliant
Yes
For Use With
Han Industrial Connectors
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Han
00 .
22
Upper current
limit set by
external factors,
i .e . connectable
wire gauge, given
current limit
Current carrying capacity
Current carrying capacity
The current carrying capacity is determined in tests which are
conducted on the basis of the DIN IEC 60 512 part 5 . The current
carrying capacity is limited by the thermal properties of materials
which are used for inserts as well as by the insulating materials .
These components have a limiting temperature which should not
be exceeded .
The relationship between the current, the temperature rise (loss
at the contact resistance) and the ambient temperature of the
connector is represented by a curve . On a linear co-ordinate
system the current lies on the vertical line (ordinate) and the
ambient temperature on the horizontal line (abscissa) which ends
at the upper limiting temperature .
In another measurement the self-heating (∆t) at different currents
is determined .
At least 3 points are determined which are connected to a parabolic
curve, the basic curve .
The corrected current carrying capacity curve is derived from this
basic curve . The reasons for the correction are external factors
that bring an additional limitation to the current carrying capacity,
i .e . connectable wire gauge or an unequal dispersion of current .
Current carrying capacity of copper wires
Example of a current capacity curve
permissible
operation
range
Depiction in accordance with DIN EN 60 204 for PVC-insulated copper wires in an ambient temperature of + 40 °C under permanent operating conditions .
For different conditions and temperatures, installations, insulation materials or conductors the relevant corrections have to be carried out .
B1
B2
C
D
Diameter [mm²] of single wires in a three-phase system
Wires in protective tubes and installation conduits
Cables and wires in protective tubes and installation conduits
Cables and wires at walls
Cables and wires on a bed
basic curve
Type of installation
Permissible upper limiting temperature
corrected curve
set by applied materials
0 .75
7 .60
–
–
–
10 .4
11 .7
11 .5
Definition: The rated current is the continuous, not interrupted
current a connector can take when simultaneous power on all con-
tacts is given, without exceeding the maximum temperature .
Acc . to IEC 61 984 the sum of ambient temperature and the tem-
perature rise of a connector shall not exceed the upper limiting
temperature . The limiting temperature is valid for a complete con-
nector, that means insert plus housing .
As a result the insert gives the limit for the temperature of a com-
plete connector and thus housings as well .
In practice it is not usual to load all terminals simultaneously with
the maximum current . In such a case one contact can be loaded
with a higher current as permitted by the current capacity curve, if
less than 20 % of the whole is loaded .
However, for these cases there are no universal rules . The
limits have to be determined individually from case to case . It is
recommended to proceed in accordance with the relevant rules of
the DIN IEC 60 512 part 5 .
1,0
9 .6
Example of a current carrying curve
13 .5
12,0
15 .2
16 .1
1 .5
Ambient temperature
18 .3
16 .5
21,0
22,0
2 .5
25
23
28
30
4
32
29
36
37
6
Permissible upper temperature-limit
10
44
40
50
52
16
60
53
66
70
set by applied materials
25
77
67
84
88
104
114
35
97
83