LMC6044IM National Semiconductor, LMC6044IM Datasheet - Page 10

OP AMP, QUAD MICROPOWER, POWERWISE

LMC6044IM

Manufacturer Part Number
LMC6044IM
Description
OP AMP, QUAD MICROPOWER, POWERWISE
Manufacturer
National Semiconductor
Datasheet

Specifications of LMC6044IM

Op Amp Type
Low Power
No. Of Amplifiers
4
Bandwidth
0.1MHz
Slew Rate
0.02V/µs
Supply Voltage Range
4.5V To 15.5V
Amplifier Case Style
SOIC
No. Of Pins
14
Operating Temperature Range
-40°C To
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LMC6044IM
Manufacturer:
NS
Quantity:
1
Company:
Part Number:
LMC6044IM
Quantity:
178
Company:
Part Number:
LMC6044IM
Quantity:
178
Part Number:
LMC6044IM/NOPB
Manufacturer:
TI
Quantity:
1 100
Part Number:
LMC6044IM/NOPB
Manufacturer:
NS/国半
Quantity:
20 000
Part Number:
LMC6044IMX
Manufacturer:
TI/德州仪器
Quantity:
20 000
Part Number:
LMC6044IMX/NOPB
Manufacturer:
NS
Quantity:
5 200
www.national.com
Application Hints
of the ultra-low bias current of the LMC6044, typically less
than 2 fA, it is essential to have an excellent layout. Fortu-
nately, the techniques of obtaining low leakages are quite
simple. First, the user must not ignore the surface leakage of
the PC board, even though it may sometimes appear accept-
ably low, because under conditions of high humidity or dust
or contamination, the surface leakage will be appreciable.
To minimize the effect of any surface leakage, lay out a ring
of foil completely surrounding the LMC6044’s inputs and the
terminals of capacitors, diodes, conductors, resistors, relay
terminals, etc. connected to the op-amp’s inputs, as in Fig-
ure 4. To have a significant effect, guard rings should be
placed on both the top and bottom of the PC board. This PC
foil must then be connected to a voltage which is at the same
voltage as the amplifer inputs, since no leakage current can
flow between two points at the same potential. For example,
a PC board trace-to-pad resistance of 10
mally considered a very large resistance, could leak 5 pA if
the trace were a 5V bus adjacent to the pad of the input. This
would cause a 100 times degradation from the LMC6044’s
actual performance. However, if a guard ring is held within 5
mV of the inputs, then even a resistance of 10
cause only 0.05 pA of leakage current. See Figure 5 for
typical connections of guard rings for standard op-amp con-
figurations.
FIGURE 4. Example of Guard Ring
in P.C. Board Layout
(Continued)
12
Ω, which is nor-
01113807
11
Ω would
10
The designer should be aware that when it is inappropriate
to lay out a PC board for the sake of just a few circuits, there
is another technique which is even better than a guard ring
on a PC board: Don’t insert the amplifier’s input pin into the
board at all, but bend it up in the air and use only air as an
insulator. Air is an excellent insulator. In this case you may
have to forego some of the advantages of PC board con-
struction, but the advantages are sometimes well worth the
effort
See Figure 6.
FIGURE 5. Typical Connections of Guard Rings
of
using
Non-Inverting Amplifier
Inverting Amplifier
point-to-point
Follower
up-in-the-air
01113809
01113808
01113810
wiring.

Related parts for LMC6044IM