NCP5810DMUTXG ON Semiconductor, NCP5810DMUTXG Datasheet
NCP5810DMUTXG
Specifications of NCP5810DMUTXG
Available stocks
Related parts for NCP5810DMUTXG
NCP5810DMUTXG Summary of contents
Page 1
NCP5810D Dual 1 W Output AMOLED Driver Supply The NCP5810D is a dual-output DC/DC converter which can generate both a positive and a negative voltage. Both PWM converters achieve high efficiency for portable application. Thanks to the high output voltage ...
Page 2
VBAT U1 11 PVIN C1 4 PGND ENABLE VBAT AVIN D1: ON NSR0320MW2 L1, L2: TDK VLF3010AT-4R7 C1: 4.7 mF 6.3 V X5R C2 6.3 V X5R 0603 C1,C3,C4: ...
Page 3
PIN FUNCTION DESCRIPTION Pin Pin Name Type 1 VOUTP OUTPUT Positive Power Output: A filter capacitor is necessary on this pin for the stability of the loop, to smooth the current flowing into the load, and limit the noise created ...
Page 4
MAXIMUM RATINGS (Note 1) Rating AVIN and PVIN Pin: Power Supply Voltage (Note 2) EN Pin: Digital Logic Input (Note 2) LXP Pin: Output (Note 2) VREF Pin: Output Reference Voltage (Note 2) VS Pin: Input (Note 2) SWN Pin: ...
Page 5
ELECTRICAL CHARACTERISTICS otherwise noted). Typical values are referenced to T Characteristic BOOST REGULATOR Positive Operational Output Voltage Range Maximum Inductor Peak Current Switches P0 ON Resistance Switches N1 ON Resistance Switches N1 Leakage Current 4 ...
Page 6
ELECTRICAL CHARACTERISTICS Typical values are referenced +25°C and V A Rating Operational Power Supply Internal Oscillator Frequency 25° Maximum Duty Cycle Stand by Current mA ...
Page 7
TYPICAL OPERATING CHARACTERISTICS 2 100 150 I (mA) OUT Figure 3. Efficiency vs MARUWA CXFU0208-4R7 Figure 5. Line Transient Response 1 VBAT, 500 mV/div DC, from 3.5 ...
Page 8
TYPICAL OPERATING CHARACTERISTICS Figure 9. Continuous Conduction Mode (CCM) 1 SWN, 5 V/div DC 100 mA/div, DC Figure 11. Positive Output Voltage Ripple in CCM mV/div AC 100 ...
Page 9
BAND GAP THERMAL TSD 1.265 V PROTECTION FBP ERROR - AMP 1.265 V + OPAMP RAMP COMP ONE SHOT OSC 1.75 Mhz ENABLE EN 400 k FBN ERROR FBN - AMP + 632.5 mV OPAMP - + 623.5 mV AGND ...
Page 10
MN1. The MAX DP monitors the pulse width and if it exceeds 88% (nom) of the cycle time the switch will be turned off. This ...
Page 11
... For example, if one needs 6.8 V. Some recommended Z zener diodes include but are not limited to: ON SEMICONDUCTOR: MM3Z6V8T1 Enable This input logic allows enabling and disabling the converter. An active high logic level on this pin enables the device. A built-in pull-down resistor disables the device if the pin is left open ...
Page 12
... Some recommended Schottky diodes include but are not limited to: ON SEMICONDUCTOR: NSR0320MW2 ON SEMICONDUCTOR: RB521S30 ROHM: RSX051VA-30 PHILIPS: PMEG2005AEL Input Capacitor Selection To achieve high performances (signal integrity) one 4.7 F 6.3 V X5R should be used to bypass the power input supply C (PVIN) and one 1 ...
Page 13
... Figure 18. Recommended PCB Layout ORDERING INFORMATION Device NCP5810DMUTXG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Demo Board Available: • The NCP5810DGEVB/D evaluation board that configures the device in typical application to supply constant voltage ...
Page 14
... C NOTE 3 0.48 *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center ...