LP3852EMP-2.5/NOPB National Semiconductor, LP3852EMP-2.5/NOPB Datasheet - Page 7
![IC, LDO VOLT REG, 2.5V, 1.5A, SOT-223-5](/photos/19/8/190851/4243346_sml.jpg)
LP3852EMP-2.5/NOPB
Manufacturer Part Number
LP3852EMP-2.5/NOPB
Description
IC, LDO VOLT REG, 2.5V, 1.5A, SOT-223-5
Manufacturer
National Semiconductor
Specifications of LP3852EMP-2.5/NOPB
Primary Input Voltage
7V
Output Voltage Fixed
2.5V
Dropout Voltage Vdo
240mV
No. Of Pins
5
Output Current
1.5A
Operating Temperature Range
-40°C To +125°C
Termination Type
SMD
Filter Terminals
SMD
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Symbol
Shutdown Input
Error Flag
AC Parameters
Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is
intended to be functional, but does not guarantee specific performance limits. For guaranteed specifications and test conditions, see Electrical Characteristics.
The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under
the listed test conditions.
Note 2: At elevated temperatures, devices must be derated based on package thermal resistance. The devices in TO220 package must be derated at θ
C/W (with 0.5in
(with 0.5in
Note 3: The human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin.
Note 4: Typical numbers are at 25°C and represent the most likely parametric norm.
Note 5: Limits are guaranteed by testing, design, or statistical correlation.
Note 6: If used in a dual-supply system where the regulator load is returned to a negative supply, the output must be diode-clamped to ground.
Note 7: The output PMOS structure contains a diode between the V
biased if the voltage at the output terminal is forced to be higher than the voltage at the input terminal. This diode can typically withstand 200mA of DC current
and 1Amp of peak current.
Note 8: Output voltage line regulation is defined as the change in output voltage from the nominal value due to change in the input line voltage. Output voltage
load regulation is defined as the change in output voltage from the nominal value due to change in load current. The line and load regulation specification contains
only the typical number. However, the limits for line and load regulation are included in the output voltage tolerance specification.
Note 9: Error Flag threshold and hysteresis are specified as percentage of regulated output voltage. See Application Hints.
Note 10: Dropout voltage is defined as the minimum input to output differential voltage at which the output drops 2% below the nominal value. Dropout voltage
specification applies only to output voltages of 2.5V and above. For output voltages below 2.5V, the drop-out voltage is nothing but the input to output differential,
since the minimum input voltage is 2.5V.
Note 11: The minimum operating value for V
Note 12: The SOT 223 package devices have slightly higher dropout due to increased bond wire resistance.
V
PSRR
T
V
T
ρ
EF(Sat)
V
I
dOFF
I
V
Td
max
e
dON
I
n(l/f)
SDT
SD
TH
lk
n
T
2
, 1oz. copper area), junction-to-ambient. See Application Hints.
2
, 1oz. copper area), junction-to-ambient (with no heat sink). The devices in the TO263 surface-mount package must be derated at θ
Parameter
Shutdown Threshold
Turn-off delay
Turn-on delay
SD Input Current
Threshold
Threshold Hysteresis
Error Flag Saturation
Flag Reset Delay
Error Flag Pin Leakage Current
Error Flag Pin Sink Current
Ripple Rejection
Output Noise Density
Output Noise Voltage
IN
is equal to either [V
Conditions
V
Output = ON
V
Output = OFF
I
I
V
(Note
(Note
I
V
V
C
V
V
C
V
f = 120Hz
BW = 10Hz – 100kHz
V
BW = 300Hz – 300kHz
V
L
L
sink
SDT
SDT
SD
Error
IN
OUT
IN
OUT
OUT
OUT
OUT
OUT
= 1.5A
= 1.5A
= V
= V
= 100µA
= V
Rising from 0.3V until
Falling from 2.0V until
= 3.3V, f = 120Hz
= 3.3V, f = 120Hz
= 2.5V
= 2.5V
= 0.5V
= 10uF
= 10uF
OUT(NOM)
9)
9)
OUT
OUT
IN
IN
and V
+ 1V
+ 0.5V
+ V
OUT
DROPOUT
7
terminals. This diode is normally reverse biased. This diode will get forward
] or 2.5V, whichever is greater.
(Note
0.02
Typ
150
100
1.3
1.3
0.8
20
25
10
73
57
1
5
1
1
1
4)
LP3852/5
Min
2
5
2
(Note
Max
0.3
0.1
16
8
5)
www.national.com
jA
µV (rms)
= 60°C/W
Units
jA
mA
nA
nA
dB
µV
µs
µs
µs
%
%
V
V
= 50°