SKYPER 32PRO R SEMIKRON, SKYPER 32PRO R Datasheet
SKYPER 32PRO R
Specifications of SKYPER 32PRO R
Related parts for SKYPER 32PRO R
SKYPER 32PRO R Summary of contents
Page 1
... SKYPER 32PRO R ... TM SKYPER IGBT Driver Core SKYPER 32PRO R Features Typical Applications Absolute Maximum Ratings Symbol Conditions Characteristics Symbol Conditions This technical information specifies semiconductor devices but promises no characteristics. No warranty or guarantee expressed or implied is made regarding delivery, performance or suitability. 26-05-2009 KRA Values Units min ...
Page 2
... High Voltage Diode for DSCP ................................................................................................................................................ 13 Gate resistors ......................................................................................................................................................................... 13 Soft Turn-Off (STO) ................................................................................................................................................................ 14 External Error Input (EEI) ....................................................................................................................................................... 14 Application Example............................................................................................................................................................... 15 Mounting Notes ...................................................................................................................................................................... 15 Environmental Conditions....................................................................................................................................................... 16 Marking................................................................................................................................................................................... 17 1 Related Documents: title: ® SKYPER 32PRO R monitoring / de-saturation monitoring (DSCP)..................................................... 11 CEsat 2009-05-26 – Rev04 Data Sheet SKYPER 32PRO R © by SEMIKRON ...
Page 3
... PLUS and MINUS of the power module. When first operating a newly developed circuit, SEMIKRON recommends to apply low collector voltage and load current in the beginning and to increase these values gradually, observing the turn-off behaviour of the free-wheeling diode and the turn-off voltage spikes generated across the IGBT ...
Page 4
... SKYPER 32PRO R Block diagram Block diagram Dimensions Dimensions in mm (bottom view) 3 (top view) ±0,2mm unless otherwise noted 2009-05-26 – Rev04 © by SEMIKRON ...
Page 5
... Digital 15 V logic; 100kOhm impedance; LOW = TOP switch off; HIGH = TOP switch on Digital 15 V logic; 100kOhm impedance; LOW = BOT switch off; HIGH = BOT switch on Stabilised +15V ±4% Stabilised +15V ±4% Dead time bit #2 Dead time bit #3 Dead time bit #1 © by SEMIKRON ...
Page 6
... Control input for setting soft turn-off BOT IGBT Output power supply 2009-05-26 – Rev04 ±0,25mm unless otherwise noted Specification 1) Stabilised +15V / max. 10mA Voltage input; 6,6kOhm impedance; LOW = ERROR 1) Stabilised -7V / max. 10mA 1) Stabilised +15V / max. 10mA Voltage input; 6,6kOhm impedance; LOW = ERROR 1) Stabilised -7V / max. 10mA © by SEMIKRON ...
Page 7
... Average Output Current as a Function of the Ambient Temperature ° ° ° ° C Min. 12,2 2009-05-26 – Rev04 =25° C amb 3 µC 4 µC 5 µC 6 µC gate charge 40 ° ° ° ° °C 90 ° C ambient temperature © by SEMIKRON 7 µC ...
Page 8
... Please note: An isolation test is not performed at SEMIKRON as a series test. Auxiliary Power Supply A few basic rules should be followed when dimensioning the customer side power supply for the driver. The following table shows the required features of an appropriate power supply ...
Page 9
... It is not permitted to apply switching pulses shorter than 1µs. 8 Application Hints A capacitor is connected to the input to obtain high noise immunity. Disabling of (PRIM_nPWRFAIL_IN) can be achieved by no connection or connection to +15V. UVP level 13,5V UVP level 12V 2009-05-26 – Rev04 the Under Voltage Reset function © by SEMIKRON ...
Page 10
... Propagation delay of the driver, interlock dead time and switching time of the IGBT chip has to be taken into account (not shown in the pulse pattern). 2009-05-26 – Rev04 > 9µs, the driver core is ready to © by SEMIKRON ...
Page 11
... IGBT chip has to be taken into account (not shown in the pulse pattern). In case both channel PRIM_BOT_IN) are at high level, the IGBTs will be turned off. If only one channel is switching, there will be no interlock dead time. 2009-05-26 – Rev04 inputs (PRIM_TOP_IN and © by SEMIKRON ...
Page 12
... GND open open open GND open open open GND open open GND CE may be controlled by an external CEref which passes after turn-on of the IGBT bl V > V and will turn off the IGBT. The error CE CEref of the IGBT during its CEstat . CE © by SEMIKRON ...
Page 13
... Short circuit during turn on CE V ⋅ CEstat VCE k Ω Ω ⋅ − µ s − µ s − ⋅ Ω µ 00323 pF and t are typical values at room CEstat bl , capacitor © by SEMIKRON ...
Page 14
... IGBT will decrease. The Goff inductive peak over voltage during turn-off will diminish. In order to ensure locking of the IGBT even when the driver supply voltage is turned off, a resistance (R 2009-05-26 – Rev04 CE (1k / 0,4W) must be VCE and R . Gon Goff ) has to be integrated. GE © by SEMIKRON ...
Page 15
... The soft turn-off time is limited to 10µs. After this time the output stage turn-off with used R . Goff Disabling of Soft Turn-Off can be achieved by R bridge. Connection example with using an external transistor in switch mode. 2009-05-26 – Rev04 and turns-off the IGBT at lower Goff cannot be recommended. The Goff_SC = 0 or wire Goff_SC © by SEMIKRON ...
Page 16
... SEC_TOP_ERR_IN Ron SEC_TOP_IGBT_ON SEC_TOP_IGBT_OFF Roff SEC_TOP_GND SEC_TOP_GND SEC_TOP_IGBT_SOFTOFF Roff_sc SEC_TOP_8N SEC_BOT_VCE_CFG BY203/20S SEC_BOT_VCE_IN 330pF SEC_BOT_15P 18k 50V SEC_BOT_ERR_IN Ron SEC_BOT_IGBT_ON SEC_BOT_IGBT_OFF Roff SEC_BOT_GND SEC_BOT_GND SEC_BOT_IGBT_SOFTOFF Roff_sc SEC_BOT_8N Finished Hole & Pad Size in mm © by SEMIKRON DC+ 10k load 10k DC- ...
Page 17
... Connection between driver core and printed circuit board mechanical reinforced by using support posts. The characteristics and further environmental conditions are indicated in the data sheet. 16 Product information of suitable support posts and distributor contact information is available at e.g. http://www.richco-inc.com LCBST). 2009-05-26 – Rev04 (e.g. series DLMSPM, © by SEMIKRON ...
Page 18
... Information furnished in this document is believed to be accurate and reliable. However, no representation or warranty is given and no liability is assumed with respect to the accuracy or use of such information. SEMIKRON does not assume any liability arising out of the application or use of any product or circuit described herein. Furthermore, this technical information may not be considered as an assurance of component characteristics ...