DSPIC30F6011A-20E/PT Microchip Technology, DSPIC30F6011A-20E/PT Datasheet - Page 12
![Digital Signal Processor](/photos/6/81/68123/c04-066_pf_sml.jpg)
DSPIC30F6011A-20E/PT
Manufacturer Part Number
DSPIC30F6011A-20E/PT
Description
Digital Signal Processor
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F2011-20ISO.pdf
(66 pages)
2.DSPIC30F2011-20IP.pdf
(26 pages)
3.DSPIC30F5011-20IPT.pdf
(220 pages)
4.DSPIC30F6011A-30IPT.pdf
(234 pages)
5.DSPIC30F6011A-30IPT.pdf
(8 pages)
6.DSPIC30F6011A-30IPT.pdf
(10 pages)
7.DSPIC30F6011A-30IPT.pdf
(6 pages)
8.DSPIC30F6011A-30IPT.pdf
(8 pages)
9.DSPIC30F6011A-30IPT.pdf
(16 pages)
Specifications of DSPIC30F6011A-20E/PT
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
CAN, I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
52
Program Memory Size
132KB (44K x 24)
Program Memory Type
FLASH
Eeprom Size
2K x 8
Ram Size
6K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 16x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
64-TFQFP
Package
64TQFP
Device Core
dsPIC
Family Name
dsPIC30
Maximum Speed
20 MHz
Operating Supply Voltage
3.3|5 V
Data Bus Width
16 Bit
Number Of Programmable I/os
52
Interface Type
CAN/I2C/SPI/UART
On-chip Adc
16-chx12-bit
Number Of Timers
5
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC30F008 - MODULE SKT FOR DSPIC30F 64TQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F6011A-20E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
DSPIC30F6011A-20E/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
dsPIC30F6011A/6012A/6013A/6014A
18. Module: LP Oscillator
19. Module: ADC
20. Module: PLL
DS80457B-page 12
The 32 kHz LP Oscillator module is not
operational for this version of silicon.
Work around
None.
Affected Silicon Revisions
ADC event triggers from the INT0 pin will not
wake-up the device from Sleep mode if the SMPI
bits are non-zero. This means that if the ADC is
configured to generate an interrupt after a certain
number of INT0 triggered conversions, the ADC
conversions will not be triggered and the device
will remain in Sleep. The ADC will perform
conversions and wake-up the device only if it is
configured to generate an interrupt after each INT0
triggered conversion (SMPI<3:0> = 0000).
Work around
None. If ADC event trigger from the INT0 pin is
required, initialize SMPI<3:0> to ‘0000’ (interrupt
on every conversion).
Affected Silicon Revisions
If 4x or 8x PLL mode is used, the input frequency
range is 5 MHz-10 MHz instead of 4 MHz-10 MHz.
Work around
None. If 4x or 8x PLL is used, make sure the input
crystal or clock frequency is 5 MHz or greater.
Affected Silicon Revisions
A2
A2
A2
X
X
X
B0
B0
B0
B1
B1
B1
21. Module: ADC
If the ADC module is in an enabled state when the
device enters Sleep mode as a result of executing
a PWRSAV #0 instruction, the device power-down
current (I
in the device data sheet. This may happen even if
the ADC module is disabled by clearing the ADON
bit prior to entering Sleep mode.
Work around
In order to remain within the I
listed in the device data sheet, the user software
must completely disable the ADC module by
setting the ADC Module Disable bit in the
corresponding Peripheral Module Disable (PMDx)
register, prior to executing a PWRSAV
instruction.
Affected Silicon Revisions
A2
X
B0
X
PD
) may exceed the specifications listed
B1
X
© 2010 Microchip Technology Inc.
PD
specifications
#0