LM2577S-ADJ National Semiconductor, LM2577S-ADJ Datasheet - Page 17
![DC/DC Converter IC](/photos/19/2/190204/4243352_sml.jpg)
LM2577S-ADJ
Manufacturer Part Number
LM2577S-ADJ
Description
DC/DC Converter IC
Manufacturer
National Semiconductor
Specifications of LM2577S-ADJ
Input Voltage
40V
Output Voltage
37V
No. Of Pins
5
Termination Type
SMD
Mounting Type
Through Hole
Output Current Max
3A
Peak Reflow Compatible (260 C)
No
Supply Voltage Max
40V
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM2577S-ADJ
Manufacturer:
NS
Quantity:
11 200
Part Number:
LM2577S-ADJ
Manufacturer:
NS/国半
Quantity:
20 000
Company:
Part Number:
LM2577S-ADJ/NOPB
Manufacturer:
National Semiconductor
Quantity:
1 981
Company:
Part Number:
LM2577S-ADJ/NOPB
Manufacturer:
Texas Instruments
Quantity:
465
Application Hints
3. Output Voltage Selection (R1 and R2)
This section is for applications using the LM1577-ADJ/
LM2577-ADJ. Skip this section if the LM1577-12/LM2577-12
or LM1577-15/LM2577-15 is being used.
With the LM1577-ADJ/LM2577-ADJ, the output voltage is
given by
Resistors R1 and R2 divide the output down so it can be
compared with the LM1577-ADJ/LM2577-ADJ internal
1.23V reference. For a given desired output voltage V
select R1 and R2 so that
4. Input Capacitor Selection (C
The switching action in the step-up regulator causes a trian-
gular ripple current to be drawn from the supply source. This
in turn causes noise to appear on the supply voltage. For
proper operation of the LM1577, the input voltage should be
decoupled. Bypassing the Input Voltage pin directly to
ground with a good quality, low ESR, 0.1 µF capacitor (leads
as short as possible) is normally sufficient.
If the LM1577 is located far from the supply source filter ca-
pacitors, an additional large electrolytic capacitor (e.g.
47 µF) is often required.
5. Diode Selection (D)
The switching diode used in the boost regulator must with-
stand a reverse voltage equal to the circuit output voltage,
and must conduct the peak output current of the LM2577. A
suitable diode must have a minimum reverse breakdown
voltage greater than the circuit output voltage, and should be
rated for average and peak current greater than I
and I
in switching regulators. Their low forward voltage drop allows
higher regulator efficiency than if a (less expensive) fast re-
covery diode was used. See Figure 12 for recommended
part numbers and voltage ratings of 1A and 3A diodes.
Cornell Dublier — Types 239, 250, 251, UFT,
300, or 350
Nichicon — Types PF, PX, or PZ
Sprague — Types 672D, 673D, or 674D
United Chemi-Con — Types LX, SXF, or SXJ
D(PK)
FIGURE 11. Aluminum Electrolytic Capacitors
Recommended for Switching Regulators
P.O. Box 128, Pickens, SC 29671
(803) 878-6311
927 East Parkway,
Schaumburg, IL 60173
(708) 843-7500
Box 1, Sprague Road,
Lansing, NC 28643
(919) 384-2551
9801 West Higgins Road,
Rosemont, IL 60018
(708) 696-2000
. Schottky barrier diodes are often favored for use
V
OUT
= 1.23V (1 + R1/R2)
(Continued)
IN
)
LOAD(max)
OUT
,
17
BOOST REGULATOR CIRCUIT EXAMPLE
By adding a few external components (as shown in Figure
13 ), the LM2577 can be used to produce a regulated output
voltage that is greater than the applied input voltage. Typical
performance of this regulator is shown in Figure 14 and Fig-
ure 15 . The switching waveforms observed during the opera-
tion of this circuit are shown in Figure 16 .
(max)
V
100V
20V
30V
40V
50V
OUT
MBR120P
MBR130P
MBR140P
FIGURE 12. Diode Selection Chart
MBR150
11DQ03
11DQ04
11DQ05
1N5817
1N5818
1N5819
1A
Schottky
MBR320P
MBR330P
MBR340P
MBR350
31DQ03
31DQ04
31DQ05
1N5820
1N5821
1N5822
3A
MUR105
MUR110
HER102
1N4933
1N4934
10DL1
Fast Recovery
1A
www.national.com
HER302
MR851
MR831
30DL1
3A