LM3578AN National Semiconductor, LM3578AN Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LM3578AN
Manufacturer Part Number
LM3578AN
Description
DC/DC Converter IC
Manufacturer
National Semiconductor
Datasheet
1.LM3578AN.pdf
(20 pages)
Specifications of LM3578AN
Input Voltage
40V
Output Voltage
1V
No. Of Pins
8
Mounting Type
Through Hole
Output Voltage Min
-1V
Voltage Regulator Type
Switching
Output Current Max
750mA
Peak Reflow Compatible (260 C)
No
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM3578AN
Manufacturer:
NS
Quantity:
1 511
Part Number:
LM3578AN
Manufacturer:
NS/国半
Quantity:
20 000
Company:
Part Number:
LM3578AN/N
Manufacturer:
NSC
Quantity:
4 100
Company:
Part Number:
LM3578AN/N
Manufacturer:
CD
Quantity:
4 120
Company:
Part Number:
LM3578ANNOPB
Manufacturer:
INTERSIL
Quantity:
3 535
www.national.com
Applications Information
DUTY CYCLE ADJUSTMENT
When manual or mechanical selection of the output transis-
tor’s duty cycle is needed, the cirucit shown below may be
used. The output will turn on with the beginning of each
oscillator cycle and turn off when the current sunk by R2 and
R3 from the non-inverting terminal becomes greater than the
current sunk from the inverting terminal.
With the resistor values as shown, R3 can be used to adjust
the duty cycle from 0% to 90%.
When the sum of R2 and R3 is twice the value of R1, the
duty cycle will be about 50%. C1 may be a large electrolytic
capacitor to lower the oscillator frequency below 1 Hz.
REMOTE SHUTDOWN
The LM2578A may be remotely shutdown by sinking a
greater current from the non-inverting input than from the
inverting input. This may be accomplished by selecting re-
sistor R3 to be approximately one-half the value of R1 and
R2 in parallel.
FIGURE 9. Maximum Duty Cycle Limiting
FIGURE 10. Duty Cycle Adjustment
00871121
(Continued)
00871123
10
EMITTER OUTPUT
When the LM2578A output transistor is in the OFF state, if
the Emitter output swings below the ground pin voltage, the
output transistor will turn ON because its base is clamped
near ground. The Collector Current with Emitter Output Be-
low Ground curve shows the amount of Collector current
drawn in this mode, vs temperature and Emitter voltage.
When the Collector-Emitter voltage is high, this current will
cause high power dissipation in the output transistor and
should be avoided.
This situation can occur in the high-current high-voltage
buck application if the Emitter output is used and the catch
diode’s forward voltage drop is greater than 0.6V. A fast-
recovery diode can be added in series with the Emitter
output to counter the forward voltage drop of the catch diode
(see Figure 2). For better efficiency of a high output current
buck regulator, an external PNP transistor should be used as
shown in Figure 16.
SYNCHRONIZING DEVICES
When several devices are to be operated at once, their
oscillators may be synchronized by the application of an
external signal. This drive signal should be a pulse waveform
with a minimum pulse width of 2 µs. and an amplitude from
Improperly Turning ON due to D2’s Forward Voltage
FIGURE 12. D1 Prevents Output Transistor from
FIGURE 11. Shutdown Occurs when V
L
is High
00871130
00871124