LM6511IM National Semiconductor, LM6511IM Datasheet - Page 2

• Manufacturer Part Number: LM6511IM
• Description: IC,VOLT COMPARATOR,SINGLE,BIPOLAR,SOP,8PIN,PLASTIC
• Manufacturer: National Semiconductor

Specifications of LM6511IM

• Rohs Compliant: NO
• Number Of Elements: 1
• Output Type: Open Collector
• Technology: Bipolar
• Input Offset Voltage: 5mV
• Input Bias Current (typ): 130nA
• Response Time: 180ns
• Single Supply Voltage (typ): 3/5/9/12/15/18/24/28V
• Dual Supply Voltage (typ): Not RequiredV
• Supply Current (max): 3.5mA
• Power Supply Requirement: Single
• Common Mode Rejection Ratio: 72dB
• Voltage Gain In Db: 92.04dB
• Single Supply Voltage (min): 2.5V
• Single Supply Voltage (max): 30V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 500mW
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC N
• Lead Free Status / Rohs Status: Not Compliant

www.national.com
V
I
I
I
V
A
CMRR
I
V
B
OS
S
STROBE
Absolute Maximum Ratings
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
DC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T
V
OS
SAT
V
IN
AC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T
V
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions the device is intended to
be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed.
Note 2: The positive input voltage limit is 30V above the negative supply voltage. The negative input voltage limit is equal to the negative supply voltage or 30V
below the positive supply voltage, whichever is less.
Note 3: The offset voltage and offset current limits are the maximum values required to drive the output within a volt of either supply with a 1 mA load. Therefore,
these parameters define an error band and take into account the worst-case effects of voltage gain and input impedance.
Note 4: This specification is for a 100 mV input step with a 25 mV overdrive.
Supply Voltage
Output to Negative Supply Voltage
Ground to Negative Supply Voltage
Differential Input Voltage
Input Voltage
Storage Temperature Range
Soldering Information:
Symbol
−
−
Symbol
SO Package
SO Package (Infrared in 15 sec)
= 0V, 50Ω ≤ R
= 0V, 50Ω ≤ R
T
(Vapor Phase in 60 sec)
R
Offset Voltage
Input Bias Current
Input Offset Current
Positive Supply Current
Negative Supply Current
Saturation Voltage
Large Signal Voltage Gain
Common Mode Rejection Ratio
Strobe ON Current
Input Voltage Range
Output Leakage Current
Response Time
L
L
≤ 50kΩ, and I
≤ 50kΩ, and I
Parameter
Parameter
L
L
= 1.0 mA unless otherwise specified
= 1.0 mA unless otherwise specified
−65˚C to +150˚C
−0.3 to +36V
(Note 4)
(Note 1)
(Note 2)
Conditions
R
(Note 3)
R
(Note 3)
V
I
∆V
(Note 5)
V
I
SINK
STROBE
215˚C
220˚C
±
IN
IN
S
S
J
J
OUT
50V
30V
30V
≤ 50 kΩ
≤ 50 kΩ
= 25˚C. Boldface limits apply at the temperature extremes. V
= 25˚C. Boldface limits apply at the temperature extremes. V
≤ 10 mV
≥ 10 mV, V
= 8 mA
= 2V
= 3 mA
Conditions
2
OUT
Operating Ratings
Power Dissipation
Output Short Circuit Duration
Junction Temperature
ESD Rating
Supply Voltage
Temperature Range
Thermal Resistance (θ
(C = +100 pF, R = 1.5 kΩ)
SO Package
= 35V,
Typical
180
Typical
0.23
1.5
1.5
2.7
1.5
2.0
0.2
38
40
72
JA
)
LM6511I
Limit
(Note 1)
V
LM6511I
+
Limit
0.50
130
200
3.5
2.0
2.5
0.4
0.4
5.0
− 1.25
20
50
5
8
5
−40˚C ≤ T
2.5V to 30V
(Limits)
170˚C/W
+
+
500 mW
Units
mA max
(Limits)
= 2.7V,
= 2.7V,
V max
V min
Units
V/mV
ns
150˚C
+85˚C
max
max
max
max
max
300V
mV
mA
nA
dB
nA
V
10s
J
≤