MCP6541T-I/LT Microchip Technology, MCP6541T-I/LT Datasheet
![IC,VOLT COMPARATOR,SINGLE,CMOS,TSSOP,6PIN,PLASTIC](/photos/6/65/66533/mfg_sc-70_sml.jpg)
MCP6541T-I/LT
Specifications of MCP6541T-I/LT
MCP6541T-I/LTTR
Available stocks
Related parts for MCP6541T-I/LT
MCP6541T-I/LT Summary of contents
Page 1
... © 2007 Microchip Technology Inc. Description The Microchip Technology Inc. MCP6541/1R/1U/2/3/4 family of comparators is offered in single (MCP6541, + 0.3V MCP6541R, MCP6541U), single with Chip Select (CS) (MCP6543), dual (MCP6542) and quad (MCP6544) configurations. The outputs are push-pull (CMOS/TTL- compatible) and are capable of driving heavy DC or capacitive loads ...
Page 2
... Units Conditions V µ OUT 5V -0. 2. -0. (Note µV/° -40°C to +125° (Note µV/° -40°C to +125° µV/° -40°C to +125° +85° (Note +125° (Note Ω||pF Ω|| 25° 25° © 2007 Microchip Technology Inc. ...
Page 3
... PHL Propagation Delay (Low-to-High) t PLH Propagation Delay Skew t PDS Maximum Toggle Frequency f MAX f MAX Input Noise Voltage E Note 1: Propagation Delay Skew is defined as: t © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3/4 = +1.6V to +5.5V Figure 1-3). Min Typ Max −0.2 V — — — — ...
Page 4
... V V – OFF Hi-Z -20 pA (typ.) V OUT 1 pA (typ.) V FIGURE 1-2: Diagram. = +25° / – Conditions OUT 0 /2, DD OUT DD V – 0 /2, DD OUT DD V – 100 mV t 100 mV PHL t PLH Propagation Delay Timing © 2007 Microchip Technology Inc. ...
Page 5
... AC and DC specifications 200 kΩ MCP654X 200 kΩ 200 kΩ 200 kΩ FIGURE 1-3: AC and DC Test Circuit for the Push-Pull Output Comparators. © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3/4 = +1.6V to +5.5V and V DD Sym Min Typ Max Units T -40 — +85 ° -40 — +125 ° ...
Page 6
... Input Hysteresis Voltage at 596 Samples -40°C to +125° 5. 1.6V DD Input Hysteresis Voltage – Linear Temp. Co.; TC (µV/°C) 1 Input Hysteresis Voltage ) -40°C to +125° 5. 1.6V Input Hysteresis Voltage – 2 Quadratic Temp. Co.; TC (µV/° Input Hysteresis Voltage ) © 2007 Microchip Technology Inc. ...
Page 7
... T = +85° +125°C -1.0 A -1.5 -2.0 Common Mode Input Voltage (V) FIGURE 2-9: Input Offset Voltage vs. Common Mode Input Voltage © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3/4 = +1.6V to +5.5V GND 6.5 V 6.0 CM 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1 ...
Page 8
... T = +125° +85° +125° +85° Common Mode Input Voltage (V) Input Bias Current, Input T = +125° +85° +25° -40°C A Power Supply Voltage (V) Quiescent Current vs – Sweep V – Common Mode Input Voltage (V) Quiescent Current vs. = 5.5V. DD © 2007 Microchip Technology Inc. ...
Page 9
... CM DD 30% 25% 20% 15 1. High-to-Low Propagation Delay (µs) FIGURE 2-21: High-to-Low Propagation Delay. © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3/4 = +1.6V to +5.5V GND 5. 1. 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 100 FIGURE 2-22: Magnitude vs. Power Supply Voltage. ...
Page 10
... V = 1.6V PLH DD PHL 100 125 Ambient Temperature (°C) Propagation Delay vs 5.5V PHL 1.6V PLH 1.6V PHL 5.5V PLH DD 10 100 1000 Input Overdrive (mV) Propagation Delay vs. Input t PHL t PLH Common Mode Input Voltage (V) Propagation Delay vs. = 5.5V. DD © 2007 Microchip Technology Inc. ...
Page 11
... V OUT 1. Start- Charging output capacitance Time (1 ms/div) FIGURE 2-33: Supply Current (charging current) vs. Chip Select (CS) pulse at V (MCP6543 only). © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3/4 = +1.6V to +5.5V GND 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2 5.5V DD 1.5 1.0 0 5.5V 0 ...
Page 12
... Input Voltage (V) FIGURE 2-37: Input Bias Current vs. Input Voltage. DS21696F-page 12 = +1.6V to +5.5V GND 25° /2, V – = GND © 2007 Microchip Technology Inc. ...
Page 13
... Digital Outputs The comparator outputs are CMOS, push-pull digital outputs. They are designed to be compatible with CMOS and TTL logic and are capable of driving heavy DC or capacitive loads. © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3/4 Symbol OUT, OUTA Digital Output (comparator A) ...
Page 14
... Protecting the Analog . In this case, the currents through 2 need to be limited by some other 2 + and below CM Figure 2-37. Applications that are and DD . Therefore, the input offset voltage is - 0.3V and V + 0.3V to ensure Figure 4-3 depicts this behavior. p-p © 2007 Microchip Technology Inc. ...
Page 15
... CS pulse. The internal CS circuitry is designed to minimize glitches when cycling the CS pin. This helps conserve power, which is especially important in battery-powered applications. © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3/4 4.4 Externally Set Hysteresis 25 Greater flexibility in selecting hysteresis (or input trip 20 points) is achieved by using external resistors ...
Page 16
... Capacitive loads will draw additional power at start-up ------------------ × ------------------ ⎛ ⎞ ⎛ ⎞ ---------------------- - --------------------- - ⎜ ⎟ ⎝ ⎠ ⎝ ⎠ ⎛ ⎞ ⎛ ⎞ ---------------------- - --------------------- - V ⎜ ⎟ ⎝ ⎠ ⎝ ⎠ Figure 2-23 can be used to determine and Figure 2-31). 2-19), especially with higher © 2007 Microchip Technology Inc. ...
Page 17
... Connect the guard ring to the inverting input pin (V –). IN © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3/4 4.9 Unused Comparators An unused amplifier in a quad package (MCP6544) should be configured as shown in circuit prevents the output from toggling and causing crosstalk ...
Page 18
... A simple bistable multi-vibrator design is shown in Figure 4-13. V supplies (V SS The output duty cycle changes with V shows an V REF DD V OUT FIGURE 4-13: and V (where RT needs to be between the power REF = GND and achieve oscillation REF MCP6541 OUT Bistable Multi-vibrator. © 2007 Microchip Technology Inc. ...
Page 19
... Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3/4 Example: I-Temp E-Temp ...
Page 20
... XXXXXXXXXXXXXX XXXXXXXXXXXXXX YYWWNNN 14-Lead SOIC (150 mil) (MCP6544) XXXXXXXXXX XXXXXXXXXX YYWWNNN 14-Lead TSSOP (MCP6544) XXXXXXXX YYWW NNN DS21696F-page 20 Example: MCP6544-I/P 0729256 MCP6544E 0729256 MCP6544 I/P 0729256 Example: MCP6544ISL 0729256 MCP6544 E/SL 0729256 Example: MCP6544I 0729 256 © 2007 Microchip Technology Inc. ...
Page 21
... Lead Width Notes: 1. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.127 mm per side. 2. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3 ...
Page 22
... E 2.20 E1 1.30 D 2.70 L 0.10 L1 0.35 0° c 0. MAX 5 – 1.45 – 1.30 – 0.15 – 3.20 – 1.80 – 3.10 – 0.60 – 0.80 – 30° – 0.26 – 0.51 Microchip Technology Drawing C04-091B © 2007 Microchip Technology Inc. ...
Page 23
... Significant Characteristic. 3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3 ...
Page 24
... NOM MAX 8 1.27 BSC – 1.75 – – – 0.25 6.00 BSC 3.90 BSC 4.90 BSC – 0.50 – 1.27 1.04 REF – 8° – 0.25 – 0.51 – 15° – 15° Microchip Technology Drawing C04-057B © 2007 Microchip Technology Inc. ...
Page 25
... Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side. 3. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3 ...
Page 26
... D .735 L .115 c .008 b1 .045 b .014 eB – INCHES NOM MAX 14 – .210 .130 .195 – – .310 .325 .250 .280 .750 .775 .130 .150 .010 .015 .060 .070 .018 .022 – .430 Microchip Technology Drawing C04-005B © 2007 Microchip Technology Inc. ...
Page 27
... Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3 ...
Page 28
... A2 0.80 1.00 A1 0.05 – E 6.40 BSC E1 4.30 4.40 D 4.90 5.00 L 0.45 0.60 L1 1.00 REF 0° – c 0.09 – b 0.19 – Microchip Technology Drawing C04-087B L MAX 1.20 1.05 0.15 4.50 5.10 0.75 8° 0.20 0.30 © 2007 Microchip Technology Inc. ...
Page 29
... Added Section 3.0 Pin Descriptions 5. Corrected package marking (See Section 5.1 “Package Marking Information”) 6. Added Appendix A: Revision History. Revision C (September 2003) Revision B (November 2002) Revision A (March 2002) • Original Release of this Document. © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3/4 on unused DS21696F-page 29 ...
Page 30
... MCP6541/1R/1U/2/3/4 NOTES: DS21696F-page 30 © 2007 Microchip Technology Inc. ...
Page 31
... SN = Plastic SOIC (150 mil Body), 8-lead SL = Plastic SOIC (150 mil Body), 14-lead (MCP6544 Plastic TSSOP (4.4mm Body), 14-lead (MCP6544) © 2007 Microchip Technology Inc. MCP6541/1R/1U/2/3/4 . Examples: a) MCP6541T-I/LT: Tape and Reel, Industrial Temperature, 5LD SC-70. b) MCP6541T-I/OT: Tape and Reel, Industrial Temperature, 5LD SOT-23. c) ...
Page 32
... MCP6541/1R/1U/2/3/4 NOTES: DS21696F-page 32 © 2007 Microchip Technology Inc. ...
Page 33
... PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Smart Serial, SmartTel, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 34
... Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2007 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 ...