PIC12F510T-I/MS Microchip Technology, PIC12F510T-I/MS Datasheet - Page 6

• Manufacturer Part Number: PIC12F510T-I/MS
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,TSSOP,8PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12F510T-I/MS

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Program Memory Size: 1.5KB (1K x 12)
• Program Memory Type: FLASH
• Ram Size: 38 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Processor Series: PIC12F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 38 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164101, DV164120, DM163029
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 3 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162070 - HEADER INTRFC MPLAB ICD2 8/14PAC164325 - MODULE SKT FOR 8MSOP
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

PIC12F510
3.1.2.5
The End Programming command terminates the
program process. A delay of T
required before the next command to allow the internal
programming voltage to discharge (see Figure 3-6).
FIGURE 3-6:
3.1.2.6
After this command is performed, the entire program
memory and Configuration Word is erased.
To perform a Bulk Erase of the program memory and
configuration fuses, the following sequence must be
performed (see Figure 3-12).
1.
2.
3.
4.
5.
DS41257B-page 6
Note 1: A fully erased part will read ‘1’s in every
Read and save 0x3FF oscillator calibration bits
and 0x404 backup OSCCAL bits into computer/
programmer temporary memory.
Enter Program/Verify mode. PC is set to Config-
uration Word address.
Perform a Bulk Erase Program Memory
command.
Wait T
Restore OSCCAL bits.
2: The oscillator calibration bits are erased if
ICSPCLK
ICSPDAT
ERA
program memory location.
a Bulk Erase is invoked. They must be
read and saved prior to erasing the
device and restored during the program-
ming operation. Oscillator calibration bits
are stored at the Reset vector as the
operand of a MOVLW instruction.
End Programming
Bulk Erase Program Memory
to complete Bulk Erase.
END PROGRAMMING (EXTERNALLY TIMED)
DIS
1
0
(see Table 6-1) is
2
1
T
3
1
SET
1
4
1
To perform a full device Bulk Erase of the program
memory, configuration fuses, user IDs and backup
OSCCAL, the following sequence must be performed
(see Figure 3-13).
1.
2.
3.
4.
5.
6.
7.
T
HLD
Read and save 0x3FF oscillator calibration bits
and 0x404 backup OSCCAL bits into computer/
programmer temporary memory.
Enter Program/Verify mode.
Increment PC to 0x400 (first user ID location).
Perform a Bulk Erase command.
Wait T
Restore OSCCAL bits.
Restore backup OSCCAL bits.
5
x
1
ERA
6
x
to complete Bulk Erase.
T
DIS
© 2007 Microchip Technology Inc.
1
Next Command
2