PIC18F2431T-I/MM Microchip Technology, PIC18F2431T-I/MM Datasheet - Page 20
![16 KB Flash, 768 RAM, 22 I/O 28 QFN-S 6x6m T/R](/photos/6/81/68120/150-28-qfn_sml.jpg)
PIC18F2431T-I/MM
Manufacturer Part Number
PIC18F2431T-I/MM
Description
16 KB Flash, 768 RAM, 22 I/O 28 QFN-S 6x6m T/R
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F818-ISO.pdf
(6 pages)
3.PIC18F2331-ISO.pdf
(392 pages)
4.PIC18F2331-ISO.pdf
(8 pages)
5.PIC18F2331-ISO.pdf
(6 pages)
6.PIC18F2331-ISO.pdf
(16 pages)
7.PIC18LF2331-ISO.pdf
(40 pages)
Specifications of PIC18F2431T-I/MM
Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, LVD, Power Control PWM, QEI, POR, PWM, WDT
Number Of I /o
24
Program Memory Size
16KB (8K x 16)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 5x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
I3-DB18F4431 - BOARD DAUGHTER ICEPIC3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC18F2431T-I/MM
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
PIC18F2331/2431/4331/4431
3.5
The boot block segment is programmed in exactly the
same manner as the ID locations (see Section 3.4).
Multi-panel writes must be disabled so that only
addresses in the range 0000h to 01FFh will be written.
The code sequence detailed in Table 3-7 should be
used, except that the address data used in “Step 2” will
be in the range 000000h to 0001FFh.
TABLE 3-8:
FIGURE 3-9:
DS30500B-page 20
Step 1: Direct access to config memory.
Step 2: Position the program counter
Step 3
Note 1:
Command
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
1111
0000
0000
1111
0000
4-Bit
(2)
2:
: Set table pointer for config byte to be written. Write even/odd addresses.
Boot Block Programming
If the code protection bits are programmed while the program counter resides in the same block, then the interaction of
code protection logic may prevent further table write. To avoid this situation, move the program counter outside the
code protection area (e.g., GOTO 100000h).
Enabling the write protection of configuration bits (WRTC = 0 in CONFIG6H) will prevent further writing of configuration
bits. Always write all the configuration bits before enabling the write protection for configuration bits.
8E A6
8C A6
EF 00
F8 00
0E 30
6E F8
0E 00
6E F7
0E 00
6E F6
<LSB><MSB ignored>
00 00
2A F6
<LSB ignored><MSB>
00 00
SET ADDRESS POINTER TO CONFIGURATION LOCATION
CONFIGURATION PROGRAMMING FLOW
Data Payload
Delay P9 Time
Configuration
Load Even
for Write
Program
Address
Done
Start
LSB
(1)
.
BSF
BSF
GOTO
MOVLW 30h
MOVWF TBLPTRU
MOVLW 00h
MOVWF TBLPRTH
MOVLW 00h
MOVWF TBLPTRL
Load 2 bytes and start programming
NOP - hold SCLK high for time P9
INCF TBLPTRL
Load 2 bytes and start programming
NOP - hold SCLK high for time P9
EECON1, EEPGD
EECON1, CFGS
100000h
programmed a byte at a time. The “Table Write, Begin
3.6
Unlike code memory, the configuration bits are
Programming” 4-bit command (1111) is used but only
8 bits of the following 16-bit payload will be written. The
LSB of the payload will be written to even addresses,
and the MSB will be written to odd addresses. The code
sequence to program two consecutive configuration
locations is shown in Table 3-8.
Core Instruction
Configuration Bits Programming
Delay P9 Time
Configuration
Load Odd
for Write
Program
Address
Done
MSB
Start
2010 Microchip Technology Inc.