SS311PT Honeywell Sensing and Control, SS311PT Datasheet
SS311PT
Manufacturer Part Number
SS311PT
Description
SENSOR HALL EFFECT BIPOLAR SMD
Manufacturer
Honeywell Sensing and Control
Type
Bipolar Latchr
Specifications of SS311PT
Sensing Range
140G Trip, -140G Release
Voltage - Supply
2.7 V ~ 7 V
Current - Supply
5.5mA
Current - Output (max)
4mA
Output Type
Digital, Open Collector
Operating Temperature
-40°C ~ 150°C
Package / Case
TO-236-3, SC-59, SOT-23-3
Hall Effect Type
Bipolar
Output Current
4mA
Sensor Case Style
SOT-23
No. Of Pins
3
Supply Voltage Range
2.7V To 7V
Operating Temperature Range
-40°C To +150°C
Operate Point Typ
55G
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SS311PT
Manufacturer:
DOESTEK
Quantity:
1 652
Installation Instructions for the
SS311PT/SS411P Bipolar Hall-effect
Digital Position Sensors with Built-in
Pull-up Resistor
GENERAL INFORMATION
CAUTION
ELECTROSTATIC DISCHARGE DAMAGE
This component is sensitive to electrostatic discharge (ESD).
Take normal ESD precautions in handling this product to
prevent ESD-induced damage and/or degradation.
Failure to comply with these instructions may result in
product damage.
SOLDERING/ASSEMBLY
SS311PT: Use an infrared reflow process with temperatures of
245 °C [473 °F] peak for 10 s max.
SS411P: PC board wave soldering temperature is 250 °C to
260 °C [482°F to 500 °F] peak for 3 s max.
Table 1. SS311PT/SS411P Specifications (At 2.7 Vdc to 7 Vdc supply, 4 mA load, TA = -40 °C to 150 °C [-40 °F to 302 °F]
Sensing and Control
CAUTION
IMPROPER SOLDERING
• Ensure leads are adequately supported during any
• Limit exposure to high temperatures.
• Do not wave solder the SS311PT.
Failure to comply with these instructions may result in
product damage.
Characteristic
Supply voltage
Supply current
Output current
Vsat
Output leakage current
Output rise time
Output fall time
Thermal resistance:
Operate
Release
Differential
Operating temperature
Storage temperature
SS311PT
SS411P
forming/shearing operation so that they are not stressed
inside the plastic case.
gauss <-140, Vs = 5 V, 25 °C [77°F]
-40 °C to 150 °C [-40 °F to 302 °F]
-40 °C to 150 °C [-40 °F to 302 °F]
-40 °C to 150 °C [-40 °F to 302 °F]
-40 °C to 150 °C [-40 °F to 302 °F]
-40 °C to 150 °C [-40 °F to 302 °F]
25 °C [77 °F]
gauss <-140
gauss >140
Condition
–
–
–
–
–
Table 1. Absolute Maximum Ratings
Note 1: Absolute maximum ratings are the extreme limits that
the device will withstand without damage to the device.
However, the electrical and mechanical characteristics are not
guaranteed as the maximum limits (above recommended
operating conditions) are approached, nor will the device
necessarily operate at absolute maximum ratings.
Figure 1. Current Sinking Output Block Diagram
Characteristic
Supply voltage
Applied output
voltage
Output current
Magnetic flux
NOTICE
Bipolar Hall-effect sensors may have an initial output in
either the ON or OFF state if powered up with an applied
magnetic field in the differential zone (applied magnetic field
>Brp and <Bop). Honeywell recommends allowing 10 µs for
output voltage to stabilize after supply voltage has reached
5 Vdc.
Minimum
-40 [-40]
-40 [-40]
-140
2.7
-30
40
–
–
–
–
–
–
–
–
–
Typical
303
233
5.0
5.5
-55
55
Min.
-0.5
-0.5
–
–
–
–
–
–
–
–
–
–
–
Typ.
Maximum
150 [302]
150 [302]
50046426
–
–
–
–
140
7.0
4.0
0.4
1.5
1.5
14
10
30
1
–
–
–
–
no limit
Max.
ISSUE 1
7.0
7.0
8.0
°C [°F]
°C [°F]
gauss
gauss
gauss
°C/W
Unit
Vdc
mA
mA
µA
µs
V
gauss
Unit
Vdc
Vdc
mA
Related parts for SS311PT
SS311PT Summary of contents
Page 1
... SS411P: PC board wave soldering temperature is 250 °C to 260 °C [482°F to 500 °F] peak for 3 s max. Table 1. SS311PT/SS411P Specifications (At 2.7 Vdc to 7 Vdc supply load -40 °C to 150 °C [-40 °F to 302 °F] Characteristic Supply voltage -40 ° ...
Page 2
... SS311PT/SS411P Figure 2. Mounting Dimensions (For reference only. mm/[in]) SS311PT Figure 3. SS311PT Tape and Reel Dimensions (For reference only. mm/[in]) WARNING PERSONAL INJURY DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. ...