NSE-5310-ASST austriamicrosystems, NSE-5310-ASST Datasheet
NSE-5310-ASST
Specifications of NSE-5310-ASST
Related parts for NSE-5310-ASST
NSE-5310-ASST Summary of contents
Page 1
... Custom packaging such as wafer-level chip scale packaging can be provided. Minimum order quantities may apply. RoHS compliant 3 Applications The NSE-5310 is ideal for Micro-actuator and servo drive feedback, Replacement for optical encoders, Optical and imaging systems, Consumer electronics, Precision biomedical devices, Instrumentation and automation, Automotive applications, and Integrated closed-loop motion systems using New Scale’ ...
Page 2
... Digital input with pull- I2C A0 11 down www.austriamicrosystems.com 1 20 TestBus3 VDD5V VDD3V3 18 4 TestBus0 17 TestBus1 5 16 NSE-5310 PWM 6 15 CSn 7 14 SCL / CLK SDA / DIO 9 I2C_A0 10 11 Special Requirements Not Connected Indicates increasing or decreasing of magnitude by the AGC. Can be used for Push Button Function. Both signals are active ...
Page 3
... NSE-5310 Data Sheet - Table 1. Pin Descriptions Pin Pin Name Pin Type Number SDA (DO) 12 Digital I/O / Tristate SCL (CLK) 13 Digital input Digital input with pull- CSn 14 up PWM 15 Digital output TestBus1 16 Analog I/O TestBus0 17 VDD3V3 18 Supply pad VDD5V 19 TestBus3 20 Analog I/O www ...
Page 4
... NSE-5310 Data Sheet - Absolute Maximum Ratings Stresses beyond those listed in Table 2 may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in maximum rating conditions for extended periods may affect device reliability. ...
Page 5
... NSE-5310 Data Sheet - Electrical Characteristics Table 3. Operating Conditions Symbol Parameter VDD5V Positive I/O Supply Voltage VDD3V3 Positive Core Supply Voltage VDDD/ VDDA Ambient Temperature T AMB Supply Current I supp 6.1 Magnet Input Specification Table 4. Two Pole Cylindrical Diametrically Magnetized Source Symbol Parameter ...
Page 6
... NSE-5310 Data Sheet - 6.2 Electrical System Specifications Table 5. Electrical System Specifications Symbol Parameter RES Resolution INL Integral non-linearity (optimum) opt INL Integral non-linearity (over temperature) temp INL Integral non-linearity Differential non-linearity DNL Transition noise TN t Power-up time PwrUp t System propagation delay ...
Page 7
... NSE-5310 Data Sheet - 6.3 DC/AC Characteristics for Digital Inputs and Outputs Table 6. CMOS Input, CMOS Input Pull Down, CMOS Input Pull Up Symbol Parameter V High Level Input Voltage IH V Low Level Input Voltage IL3V3 High Level Input Voltage Low Level Input Voltage ...
Page 8
... Data Sheet - Detailed Description The TRACKER measures the spatially varying magnetic field produced by moving a multi-pole magnetic strip over a Hall sensor array on the NSE-5310 chip (see Figure 3). The internal sinusoidal (SIN) and phase-shifted sinusoidal (COS) signals are filtered and transformed into angle (ANG) and magnitude (MAG), representing the absolute linear position within pole pair on the magnet. Interpolation with 12 bit (4096) resolution yields 0.5 µ ...
Page 9
... Over Travel 1 ½ poles either end A system controller and user-supplied flash memory with the TRACKER NSE-5310 provide for long-range absolute position information that is retained during sleep mode or power-down. Figure 5. Example of Absolute long-range position information with use of external flash memory and controller ...
Page 10
... NSE-5310 Data Sheet - 7.1 Using 3. Operation For 3.3V operation: Bypass the voltage regulator (LDO) by connecting VDD3V3 with VDD5V. For 5V operation: Connect the 5V supply to pin VDD5V. VDD3V3 (LDO output) must be buffered by a 2.2µF to 10µF capacitor placed close to the supply pin. ...
Page 11
... Application Information Figure 7. TRACKER NSE-5310 Evaluation Board Figure 7 shows NSE-5310 SOIC mounted on a PCB with FPC connector for ease of handling. A multipole linear magnetic strip is positioned above the sensor. 8.1 Hall Sensor Array Eight Hall Sensor Front End cells are connected to two current summation busses which end into two Active Load circuits. The Hall elements are arranged in an even linear array ...
Page 12
... Both signals are high for saturation of the AGC counter (running into upper / lower limit) and produce a Non-Valid-Range alarm. The output pins can be connected together in wired-OR configuration to produce a single NVRn bit. For faster power-up and response time, a successive approximation algorithm is implemented. 8.3 Temperature Sensor The Temperature Sensor provides the junction temperature information over the serial interface ...
Page 13
... AGC is out of range. The I²C readout can be stopped after every byte with the stop condition P. Timing constraints are according to I2C-Bus Specification V2.1 / 2000. 8.4.1 Sync Mode This mode is used to synchronize the external electronics with the NSE-5310. In this mode two signals are provided at the pins DTEST_A and DTEST_B. Figure 11. Sync Mode ...
Page 14
... Pulse Width Modulation (PWM) Output The NSE-5310 also provides a pulse width modulated output (PWM), whose duty cycle is proportional to the relative linear position of the magnet within one pole pair (2.0 mm). This cycle repeats after every subsequent pole pair: Where: Digital position = 0 – ...
Page 15
... Magnetic Strip Requirements The NSE-5310 requires a magnetic strip with alternate poles (North-South) of pole length and pole pair length of 2 mm. A half pole is required at each end of the strip. The length of the strip determines the maximum measured stroke; it must greater than the stroke increments (1 ...
Page 16
... Data Sheet - Lateral Stroke of Multi-pole Strip Magnets: are covered by the magnet in either direction. The Hall array on the NSE-5310 has a length of 2.0mm, hence the total stroke is: maximum lateral Stroke = Length of active area – length of Hall array Note: Active area in length is defined as the area containing poles with the specified 1.0mm pole length. Shorter poles at either edge of the magnet must be excluded from the active area ...
Page 17
... NSE-5310 Data Sheet - Package Drawings and Markings Figure 14. 20-pin TSSOP Package Die C/L 3.0475±0.235 TSSOP20 (CSOIC20 Eng. Smp TestBus3 20 2 MagIncrn VDD5V 19 3 MagDecrn VDD3V3 18 4 DTest1_A TestBus0 17 5 DTest2_B TestBus1 16 6 TestCoil PWM 15 7 Mode_Index CSn 14 8 VSS SCL / CLK 13 ...
Page 18
... NSE-5310 Data Sheet - The evaluation kit includes an NSE-5310 mounted in a TSSOP 20 package with flex cable, for easy handling during evaluation and system development. The TRK-1T02-E evaluation pack includes a TRK-1T02 along with a suitable linear magnetic strip, a MC-31MB interface card and New Scale Pathway™ software with intuitive user interface to facilitate evaluation. ...
Page 19
... NSE-5310 Data Sheet - Custom chip-on-board packaging can be provided for qualified OEMs. Minimum order quantities apply. Inquire for more detail. Figure 16. Custom Chip-On-Board Packaging (5.4 x 4.2 x 0.6 mm) Custom wafer-level chip scale packaging can be provided for qualified OEMs. Minimum order quantities apply. Inquire for more detail. ...
Page 20
... Evaluation Pack NSE-5310ASDF Die thickness 300µm ±25µm NSE-5310ASSU Die thickness 300µm ±25µm NSE-5310ASST Die thickness 300µm ±25µm Custom chip-on-board Note: All products are RoHS compliant and Pb-free. Buy our products or get free samples online at ICdirect: ...
Page 21
... No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services ...