AMN13111 Panasonic Electric Works, AMN13111 Datasheet - Page 9
![SENSOR MOTION DIG SPOT 5V BK PCB](/photos/19/50/195058/amn23111_amn43121_amn13111_sml.jpg)
AMN13111
Manufacturer Part Number
AMN13111
Description
SENSOR MOTION DIG SPOT 5V BK PCB
Manufacturer
Panasonic Electric Works
Series
NaPiOn™r
Specifications of AMN13111
Sensing Distance
16.40' (5m)
Sensor Type
Passive Motion
Sensing Object
*
Response Frequency
*
Material - Body
*
Shielding
*
Voltage - Supply
3 V ~ 6 V
Output Type
Digital
Terminal Type
PC Pin
Package / Case
Radial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
255-1850
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AMN13111
Manufacturer:
KODENSHI
Quantity:
700
NOTES FOR USING MOTION SENSOR (Common)
SAFETY PRECAUTIONS
Head the following precautions to
prevent injury or accidents.
• Do not use these sensors under any
circumstances in which the range of their
ratings, environment conditions or other
specifications are exceeded. Using the
sensors in any way which causes their
specifications to be exceeded may
generate abnormally high levels of heat,
emit smoke, etc., resulting in damage to
the circuitry and possibly causing an
accident.
NOTES FOR MOTION SENSOR
1. Ambient operating conditions
1) Temperature: Refer to the absolute
maximum ratings for the temperature of
each individual sensor.
2) Humidity: 15% to 85% RH (No freezing
nor condensation at low temperature)
3) Atmospheric pressure: 86 to 106 kPa
4) Because the humidity range differs
depending on the ambient temperature,
the humidity range indicated below
should be used. Continuous operation of
the switch is possible within this range,
but continuous use near the limit of the
range should be avoided.
This humidity range does not guarantee
permanent performance.
(Avoid freezing when
used at temperatures
lower than 0°C 32°F)
(Avoid freezing when
used at temperatures
lower than 0°C 32°F)
<MA Motion Sensor>
<MP Motion Sensor>
–25
–13
–20
–4
Tolerance range
Tolerance range
85
15
85
15
+32
+32
0
0
(Avoid
condensation
when used at
temperatures
higher than 0°C
32°F)
(Avoid
condensation
when used at
temperatures
higher than 0°C
32°F)
Humidity, %R.H.
Humidity, %R.H.
Temperature, °C
Temperature, °C
140
60
°F
°F
167
75
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
NOTES FOR USING MOTION SENSOR (Common)
• Before connecting a connector, check
the pin layout by referring to the
connector wiring diagram, specifications
diagram, etc., and make sure that the
connector is connected properly. Take
note that mistakes made in connection
may cause unforeseen problems in
operation, generate abnormally high
levels of heat, emit smoke, etc., resulting
in damage to the circuitry.
In general, degradation of electronic
devices accelerates when they are
operated under conditions of high
temperature or high humidity. Before use,
confirm the reliability of the sensors
under the expected operating conditions.
5) The sensors do not have a water-proof
or dust-proof construction. Depending on
the ambient operating conditions, some
means of providing protection from water
and dust and preventing the formation of
ice and condensation must be provided
prior to using the sensors. If a sensor is
used with a cover installed, the initial
detection performance specifications
may not be able to be met. Confirm the
operation under the actual operating
conditions.
6) Take care to avoid exposing the
sensors to heat, vibration or impact since
malfunctioning may result.
2. Concerning external surge voltages
Since the internal circuitry may be
destroyed if an external surge voltages is
supplied, provide an element which will
absorb the surges. The levels of the
voltage surges which the sensor can
withstand is given below.
MA motion sensors: 500 V (±1.2 x 50µs
unipolar full-wave voltage)
MP motion sensors: Within the supply
voltage given in the absolute maximum
ratings.
• Do not use any motion sensor which
has been disassembled or remodeled.
• Protection circuit recommended
The possible failure mode is either open
or short of the output transistor. An
excess heat is the cause for short mode
failure. For any important and serious
application in terms of safety, add
protection circuit or any other protection
method.
3. Concerning power supply-
superimposed noise
1) Use a regulated power supply as the
power supply. Otherwise, power supply-
superimposed noise may cause the
sensors to malfunction. The levels of
noise which the sensor can withstand is
given below.
MA motion sensors: ±200 V (50ns, 1µs
wide square waves)
MP motion sensors: ±20 V (50ns, 1µs
wide square waves)
2) To maintain the power supply noise
performance, be certain to connect a
capacitor (33µF or more) to the sensor
power supply input terminal in order to
stabilize the power supply voltage.
4. Drop damage
If the sensor is dropped, damage can
occur resulting in incorrect operation. If
dropped, be sure to do a visual check of
the exterior for noticeable damage and
check the operation characteristics for
faulty operation.
5. Concerning the circuit sides
Since the circuit sides given in this
catalog are not protected in terms of
circuit design, check out the performance
and reliability of the circuits prior to using
the sensors.