B57164K222J EPCOS Inc, B57164K222J Datasheet - Page 17
![THERMISTOR NTC 2.2K OHM 5% RAD](/photos/16/24/162465/varistor__leaded_sml.jpg)
B57164K222J
Manufacturer Part Number
B57164K222J
Description
THERMISTOR NTC 2.2K OHM 5% RAD
Manufacturer
EPCOS Inc
Series
B57164r
Type
NTCr
Datasheet
1.B57164K0100K000.pdf
(24 pages)
Specifications of B57164K222J
Resistance In Ohms @ 25°c
2.2K
Resistance Tolerance
±5%
B Value Tolerance
±3%
B25/100
3900K
Operating Temperature
-55°C ~ 125°C
Power - Max
450mW
Lead Length
1.42" (36.00mm)
Mounting Type
PCB, Through Hole
Package / Case
Molded Disc
Resistance
2.2 KOhms
Tolerance
5 %
Termination Style
Radial
Operating Temperature Range
- 55 C to + 125 C
Dimensions
5.5 mm Dia. x 5 mm W x 36 mm L
Lead Spacing
5 mm
Power Rating
450 mW
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
B0/50
-
B25/50
-
B25/75
-
B25/85
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
B57164K 222J
B57164K0222J000
B57164K0222J000
Mounting instructions
1
1.1
Leaded thermistors comply with the solderability requirements specified by CECC.
When soldering, care must be taken that the NTC thermistors are not damaged by excessive
heat. The following maximum temperatures, maximum time spans and minimum distances have
to be observed:
Bath temperature
Soldering time
Distance from thermistor
Under more severe soldering conditions the resistance may change.
1.2
In case of NTC thermistors without leads, soldering is restricted to devices which are provided
with a solderable metallization. The temperature shock caused by the application of hot solder
may produce fine cracks in the ceramic, resulting in changes in resistance.
To prevent leaching of the metallization, solder with silver additives or with a low tin content
should be used. In addition, soldering methods should be employed which permit short soldering
times.
2
Pressure contacting by means of clamps is particularly suitable for applications involving frequent
switching and high turn-on powers.
3
The leads meet the requirements of IEC 60068-2-21. They may not be bent closer than 4 mm
from the solder joint on the thermistor body or from the point at which they leave the feed-
throughs. During bending, any mechanical stress at the outlet of the leads must be removed. The
bending radius should be at least 0.75 mm.
Tensile strength:
Please read Cautions and warnings and
Important notes at the end of this document.
Temperature measurement and compensation
Leaded NTC thermistors, lead spacing 5 mm
Soldering
Leaded NTC thermistors
Leadless NTC thermistors
Clamp contacting
Robustness of terminations (leaded types)
Test Ua1:
Leads
0.25 <
0.35 <
0.50 <
0.80 <
Dip soldering
max. 260 C
max. 4 s
min. 6 mm
0.25 mm =
0.35 mm =
0.50 mm =
0.80 mm = 10.0 N
1.25 mm = 20.0 N
Page 17 of 24
Iron soldering
max. 360 C
max. 2 s
min. 6 mm
1.0 N
2.5 N
5.0 N
B57164K
K164