AHF22 Panasonic Electric Works, AHF22 Datasheet - Page 2

• Manufacturer Part Number: AHF22
• Description: SENSOR TILT 25-60DEG TH
• Manufacturer: Panasonic Electric Works

Specifications of AHF22

• Operating Angle: 25° ~ 60°
• Mounting Type: Through Hole, Horizontal
• Operating Temperature: -20°C ~ 80°C
• Package / Case: PCB Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

SPECIFICATIONS
Notes:
1.Without any indications, specifications are measured at following conditions
• Temperature: 15 to 35°C
• Humidity: 25 to 85% RH
• Atmospheric pressure: 86 to 106 kpa.
2.The evaluation criteria for performance are as follows:
Basic characteristics – T
DIMENSIONS
• Horizontal mounting type
• Vertical mounting type
Electrical and mechanical life
Vibration resistance
Shock resistance
Terminal strength
Dropping individual part
High temperature, high humidity
storage ability
High temperature storage ability
Low temperature storage ability
Shock and heat resistance
Resistance to hydrogen sulfide
Resistance to sulfur dioxide gas
Resistance to ammonia gas
Resistance to dust
Ambient temperature
Item
Terminal No. 4
(Photo transistor: Emitter)
Horizontal
datum line
PC
board
a
Terminal No. 1
Terminal No. 4
= 25°C and applicable circuit conditions
Terminal No. 1
(LED: Anode)
9.5 dia.
11.5
11.5±0.5
3.0
4.0
7.9
9.5
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
588 m/s
Min. 9.8 N (each direction)
Three times from height of 100 cm
Leave for 500 hours at 85°C
Leave for 500 hours at –25°C (No freezing at low temperature)
Subject to 100 cycles each consisting of 30 minutes at –25°C and 30 minutes at 85°C.
Leave for 500 hours in an atmosphere containing 3 ppm of hydrogen sulfide at 40°C and 75% RH.
Leave for 500 hours in an atmosphere containing 10 ppm of sulfur dioxide at 40°C and 95% RH
Leave for 96 hours in an atmosphere containing 3% of ammonia gas at normal temperature and humidity.
Mix with 2 kg/m
–20 to +80°C (No freezing nor condensation at low temperature)
Min. 10
At 6 cpm; Opening and closing position: 0 deg. ↔ 90 deg. (The internal shpere must be stationary for at least
500 ms at angles of 0 and 90 deg. respectively.)
10 to 400 Hz acceleration 2.9 m/s
5 to 10 Hz at half amplitude of 5 mm, 5×10
Leave for 500 hours at 85°C and 85% RH
(No freezing at low temperature)
Terminal No. 2
(LED: Cathode)
Terminal No. 3
Terminal No. 3
(Photo transistor: Collector)
6.55
5
1.75
Terminal No. 2
2
(Using the applicable circuit)
applied 3 times in each of 6 directions
9.3
2.6
PC board
3.7
5.1±0.4 0.9
3
C0.3
talcum powder or fly ash and leave to stand for 8 hours
3.1±0.4
3.1
5.1
9.5
2.6
0.9
C0.3
Horizontal
datum line
2
applied for 7 days
1) Operation characteristics (operation speed 6 degrees/sec.)
• Operation angle (Output: V
• Return angle (Output: V
2) Output (V
• V
• V
OL
OH
5
(photo transistor ON): 1.2 V max. (horizontal)
cycles
(photo transistor OFF): 3.8 V min. (inclined at an angle of at least 60 degrees)
Specificaitons
O
) characteristics (The sphere must be stationary.)
OH
→ V
OL
→ V
OL
): 20 degrees min.
OH
Terminal No. 4
(Photo transistor: Emitter)
PC board pattern (Bottom view)
PC board pattern (Bottom view)
3.1±0.1
Terminal No. 1
(LED: Anode)
): 25 to 60 degrees
Terminal No. 1
(LED: Anode)
Terminal No. 4
(Photo transistor: Emitter)
3.1±0.1
11.9±0.1
1.3 dia.
11.9±0.1
1.3 dia.
Terminal No. 2
(LED: Cathode)
Terminal No. 3
(Photo transistor:
Collector)
Terminal No. 3
(Photo transistor:
Collector)
5.1±0.1
5.1±0.1
Terminal No. 2
(LED: Cathode)
AHF2
mm