LC1D18P7 SQUARE D, LC1D18P7 Datasheet - Page 51

• Manufacturer Part Number: LC1D18P7
• Description: IEC Contactor
• Manufacturer: SQUARE D

Specifications of LC1D18P7

• No. Of Poles: 3
• Contact Configuration: 3PST-NO
• Relay Mounting: DIN Rail
• Width: 45mm
• Relay Terminals: Screw Clamp
• Operating Voltage: 600VAC
• Switching Power Ac1: 3hp
• Switching Power Ac3: 15hp
• Switching Current Ac1: 32A
• Switching Current Ac3: 18A
• Load Current Inductive: 18A
• Load Current Resistive: 32A

01/04
LC2K09004
LC8K09105
Selection of Reversing Contactors for Resistive Loads
Three- and Four-Pole Contactors for AC Control Circuits
The tables below show general purpose and sensitive-environment three-pole reversing and four-pole
change over contactors for AC control circuits. The sensitive-environment contactors are recommended
for use in areas sensitive to noise, high interference mains supplies, and so forth. The contactors
incorporate an integrated mechanical interlock.
Both types of contactors mount on 35 mm DIN rails or with 4 mm (# 6) screws. The wire termination
screws are in the open, “ready-to-tighten” position. In addition, the sensitive-environment contactors
include a coil with a built-in rectifier and suppressor. Customer wiring is required to connect coil
terminations to the electrical interlock; see page 60 (top row, center wiring diagram).
For information on add-on auxiliary contact blocks and accessories, see page 54 to 58.
General-Purpose Contactors
Sensitive-Environment Contactors
Non-inductive
loads Category
AC-1 Maximum
current at
(122 °F)
A
20
20
f For mains supplies with a high level of interference (voltage surge > 800 V), use a suppressor module LA4KE1FC (50 to 129 V) or
p Use voltage codes on page 52 “Voltage Code Table” to complete catalog number.
q Pre-wired power circuit connections are standard on screw clamp versions.
LAFKE1UG (130 to 250 V), see page 56.
50 °C
Type of Connection
Screw clamp
Slip-on 1 x 0.25 in. or 2 x 0.11 in.
Solder pins for circuit board
Spring terminals
Screw clamp
Slip-on 1 x 0.25 in. or 2 x 0.11 in.
Solder pins for circuit board
q
q
f
Power
Poles
N.O.
3
3
4
3
3
4
3
3
4
3
3
4
3
3
4
3
3
4
3
3
4
Selection of Contactors for Resistive Loads
N.C.
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Auxiliary
Contacts
N.O.
1
–
–
–
1
–
1
–
–
1
–
–
1
–
–
–
1
–
1
–
–
N.C.
–
1
–
1
–
–
1
–
–
1
–
–
–
1
–
1
–
–
1
–
–
©
2001-2004 Schneider Electric All Rights Reserved
LC2K0910
LC2K0901
LC2K09004
LC2K09107
LC2K09017
LC2K090047
LC2K09105
LC2K09015
LC2K090045
LC2K09103
LC2K09013
LC2K090043
LC8K0910
LC8K0901
LC8K09004
LC8K09107
LC8K09017
LC8K090047
LC8K09105
LC8K09015
LC8K090045
Catalog
Number
f
f
p
Weight lb. (kg)
0.86 (0.390)
0.86 (0.390)
0.84 (0.380)
0.81 (0.370)
0.81 (0.370)
0.81 (0.370)
0.95 (0.430)
0.95 (0.430)
0.95 (0.430)
0.86 (0.390)
0.86 (0.390)
0.86 (0.390)
1.05 (0.480)
1.05 (0.480)
1.03 (0.470)
1.01 (0.460)
1.01 (0.460)
1.01 (0.460)
1.14 (0.520)
1.14 (0.520)
1.14 (0.520)
51