SMB55RA BANNER ENGINEERING, SMB55RA Datasheet - Page 9

• Manufacturer Part Number: SMB55RA
• Description: Sensor Mounting Bracket
• Manufacturer: BANNER ENGINEERING

Specifications of SMB55RA

• For Use With: R58E Series Expert Register Mark Sensors
• Lead Free Status / Rohs Status: RoHS Compliant part

Supply Voltage and Current
Supply Protection Circuitry
Output Configuration
Output Rating
Output Protection Circuitry
Output Response Time
Repeatability
Tri-Color LED
Sensing Image
Adjustments
Indicators
Construction
Environmental Rating
Connections
Operating Conditions
Vibration and
Mechanical Shock
Application Notes
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: [phone]
10 to 30V dc (10% max. ripple);
Supply current (exclusive of load current): 7 5 mA @ 10V dc
Protected against reverse polarity and transient voltages
Outputs are bipolar: one current sourcing (PNP) and one current sinking (NPN) open-collector transistor
100 mA max. (each output)
OFF-state leakage current: NPN < 200 microamps; PNP < 10 microamps (see Application Note 1)
NPN saturation: < 1.6V @ 100 mA
PNP saturation: < 3V @ 100 mA
Protected against false pulse on power-up and continuous overload or short-circuit of outputs.
50 microseconds
15 microseconds
Rectangular: 1.2 mm x 3.8 mm (0.05" x 0.15") at 10 mm (0.39") from face of lens; image oriented either parallel or
perpendicular to sensor length, depending on model (see page 1).
Red: 636 nm
Using push buttons (“+” Dynamic and “-” Static):
Using Remote TEACH input (gray wire):
8-segment Bargraph display: Red signal strength indicator relative to taught signal level; higher segment number for
higher sensing contrast
Light Operate: Green
Dark Operate: Green
Outputs Conducting: Yellow Power/Run Mode: Green
Zinc alloy die-cast and steel housing with black painted finish and o-ring sealed lens and lens port cap.
Lens: Acrylic
Push buttons: Thermoplastic elastomer
IEC IP67; NEMA 6
PVC-jacketed 5-conductor 2 m (6.5') or 9 m (30') attached cable with internal strain relief, integral 5-pin Euro-style
QD fitting, or 150 mm (6") pigtail with 5-pin Euro-style QD fitting. Mating QD cordsets are purchased separately. See
Quick-Disconnect cordsets on page 10.
Temperature: −10° to +55° C (+14° to 131° F)
Storage Temperature: −20° to +80° C (−4° to +185° F)
Maximum Relative Humidity: 90% at 50° C (non-condensing)
All models meet IEC 68-2-6 and IEC 68-2-27 testing criteria.
1. NPN OFF-state leakage current is < 200 μA for load impedances > 3kΩ or optically isolated loads.
2. Do not mount the sensor directly perpendicular to shiny surfaces; position it at approximately a 15° angle in relation
3. Minimize web or product “flutter” whenever possible to maximize sensing reliability.
For load current of 100 mA, leakage is < 1% of load current.
to the sensing target (see page 8).
Manually adjust discrete output switchpoint using “+” or “-” buttons
Dynamic TEACH (teach on-the-fly) sensitivity adjustment
Static TEACH sensitivity adjustment
Light operate/Dark operate
OFF-delay/ON-delay
Sensing beam color enable/disable
Dynamic TEACH (teach on-the-fly) sensitivity adjustment
Static TEACH sensitivity adjustment
Light operate/Dark operate
OFF-delay/ON-delay
Sensing beam color enable/disable
Disable push buttons for security
NOTE: 1 second delay on power-up; outputs do not conduct during this time.
Green: 525 nm
R58 Expert
Specifications
Blue: 472 nm
OFF-Delay: Green
ON-Delay: Green
35 mA @ 30V dc
™
Lens port cap and lens holder: ABS
Labels: Polycarbonate
Registration Mark Sensors
P/N 122928 rev. C
9