SMB55F BANNER ENGINEERING, SMB55F Datasheet - Page 7

• Manufacturer Part Number: SMB55F
• Description: Sensor Mounting Bracket
• Manufacturer: BANNER ENGINEERING

Specifications of SMB55F

• For Use With: R58E Series Expert Register Mark Sensors

* If the new color setting has only one sensing beam color enabled, the sensor will switch to that color for sensing.
If the new color setting has multiple sensing beam colors enabled, the sensor will use the color that was active prior to configuration; following the next TEACH procedure, it will
select the enabled sensing beam color that has the greatest contrast.
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: [phone]
• P ress and hold both
• Release push buttons.
• C lick Static (–) or Dynamic (+)
• Not available using push buttons.
• F rom SETUP mode, press and hold
• C lick Static (–) or Dynamic (+)
• P ress and hold
• T hen press and hold
• Or wait > 60 seconds.
push buttons
> 2 seconds.
push button to toggle between
choices:Dynamic (+) — increment
Static (–) — decrement
Dynamic (+) push button > 2 seconds.
push button to toggle between
choices:Dynamic (+) — increment
Static (–) — decrement
Static (–) push button
> 2 seconds to return
to SETUP mode.
both push buttons
> 2 seconds to
return to RUN mode.
0.04 sec. ≤ “click” ≤ 0.8 sec.
Push Button
T
T
T
> 2 seconds
T
T
T
T
T
T
> 2 seconds
> 2 seconds
or
or
T
T
T
T
T
T
T
Procedure
T
T T T
> 2 seconds
> 2 seconds
T
T
T
T
T
> 2 seconds
T
T
T
T
T
T
T
T
• Double-pulse the remote line.
• Wait > 8 seconds.
• E nter sequential pulses to toggle
• F rom RUN mode, three-pulse the
• F rom SETUP mode, four-pulse the
• E nter sequential pulses to toggle
• F our-pulse the remote line to return to
• H old the remote line low > 2 seconds to
• Or wait > 60 seconds.
T
between choices:
Single-pulse — increment
Double-pulse — decrement
remote line.
remote line.
between choices:
Single-click — increment
Double-click — decrement
SETUP mode.
return to RUN mode.
T
T
R58 Expert
T T T
T T T
T
T
T
T
T
T
SETUP Configuration
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
0.04 sec. ≤ “T” ≤ 0.8 sec.
T
T
T T T
T T T
T
T
T
T
T
T
T
T
T
T
T
T
T
> 2 seconds
> 2 seconds
Remote Line
T T T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
> 2 seconds
T
T
T
T
T
T
T
T
T
T
T
T
or
or
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
0.8 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
™
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T T T
T T T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
0.8 seconds
0.8 seconds
T T T
Registration Mark Sensors
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
0.8 seconds
0.8 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
0.8 seconds
T
• 8-Segment display turns OFF.
• Sensor is in SETUP mode.
• S ensor is ready to select a new setting
• S ensor steps between LO/DO and Delay setting
• S ensor toggles between LO/DO settings
• S ensor displays currently selected sensing beam
• V isible sensing beam also provides indication of
• S ensor steps between possible sensing beam
• V isible sensing beam also provides indication of
• S ensor returns to RUN mode with new settings.
• T hese steps will return to RUN mode from both
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
SETUP modes.
combination.
combinations, as shown in Figure 4.
on-the-fly, and continues in RUN mode.
color combinations, as shown in
Figure 5.
enabled sensing beam color(s).
color combinations, as shown in Figure 5.*
enabled sensing beam color(s).
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
0.8 seconds
0.8 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
0.8 seconds
Result
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
P/N 122928 rev. C
7